			Home About us Contact

Processing Behavior (processing + behavior)

Distribution by Scientific Domains

Polymers and Materials Science	75%

Selected Abstracts

Processing behavior of polycarbonate/functionalized-ethylene copolymer blends

POLYMER ENGINEERING & SCIENCE, Issue 12 2000
Marcos L. Dias
The melt blending of polycarbonate (PC) and ethylene-methacrylic acid copolymers (EFC) either in the acid form (EFC-H) or partially neutralized with sodium (EFC-Na) or zinc (EFC-Zn) was investigated. Torque monitoring of the blending showed that the polymers are capable of reacting generating new chemical species that increase the melt viscosity. As general behavior, the torque curves pass by a maximum that takes place before 30 min, the final torque being higher than that of the individual polymers. SEC analyses reveal that PC degradation also occurs and is stronger in the case of blends with EFC-Na that acts to catalyze PC degradation, promoting CO2 formation. FTIR studies on chloroform insoluble fractions of the PC/EFC-Zn blends showed that in addition to a very small number of carbonate groups, feature absorption bands of aromatic ester and hydroxyl groups appear in the new chemical species formed during the reactive processing. [source]

Polylactide copolymers: Effect of copolymer ratio and end capping on their properties

ADVANCES IN POLYMER TECHNOLOGY, Issue 2 2005
D. M. Bigg
Abstract Racemic copolymers of polylactic acid were investigated to determine the effect of copolymer ratio on melting point, degree of crystallinity, mechanical properties, and processing behavior. The copolymer ratio was found to have a strong influence on the crystallization behavior of the polymer. In addition to the ratio of the L -form to a random mixture of the D and L forms of the lactic acid in the copolymer, the effect of the polymer's molecular weight was examined. The copolymers were produced from the lactide form of the monomer to achieve weight average molecular weights above 100,000. The molecular weight had a profound influence on processability and rate of crystallization. Other notable factors influencing the properties and processing of the copolymers were the concentration of residual monomer in the polymer, the processing time-temperature history, and the extent of molecular weight degradation during processing. An important factor in the commercial development of biodegradable polymers is the ability to control the rate of degradation. Ideally, the polymer should not degrade during functional use, but degrade quite rapidly when discarded. This paper discusses various aspects associated with the control of the rate of degradation of polylactide copolymers; both from the perspective of stabilizing the polymer during processing and product use, and subsequently accelerating the rate of degradation after disposal. Of particular interest are the influences of molecular weight, crystallinity, end capping, and plasticization. © 2005 Wiley Periodicals, Inc. Adv Polym Techn 24:69,82, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/adv.20032 [source]

Short fibers as reinforcement of rubber compounds

POLYMER COMPOSITES, Issue 4 2002
M. A. López Manchado
The effect of aramid, glass and cellulose short fibers on the processing behavior, crosslinking density and mechanical properties of natural rubber (NR), ethylene-propylene-diene terpolymer rubber (EPDM) and styrene-butadiene rubber (SBR) has been investigated. Two fiber percentages (10 and 20 phr) were added to the rubber. The results have shown that the above-mentioned fibers, especially aramid fibers, are effective reinforcing agents for these rubbers, giving rise to a significant increase in mechanical properties, such as tensile modulus and strength, and tear and abrasion resistance. Moreover, a significant decrease in the time to reach 97% of curing, t,c (97) is observed, which indicates that the fibers tend to increase the vulcanization rate, regardless of the rubber used. Fibers give also rise to an increase in crosslinking, especially the aramid fibers. [source]

Processing of short-fiber reinforced polypropylene.

POLYMER ENGINEERING & SCIENCE, Issue 1 2000

An experimental investigation of the processing of glass fiber reinforced polypropylene is presented. Final fiber orientation distribution, fiber distribution in filament sections, rheological properties, final fiber length distribution and surface morphology were analyzed. This analysis was done taking into account the quantity of fibers and their interactions and flow conditions. The final fiber orientation increased when shear rate increased and fiber concentration decreased. Moreover, inhomogeneities in fiber distribution increased as the concentration of fibers decreased. The density profile showed a significant variation with fiber concentration, but it was not dependent on the shear rate applied. The viscosity showed a linear dependence with shear rate. The average fiber length and the breadth of this distribution decreased with the increasing fiber concentration and extrusion rate. The extruded filament surface showed minor roughness when the shear rate increased or when the fiber concentration decreased. The results of this experimental characterization give useful information to determine the influence of the processing variables on the final properties of short-fiber reinforced polypropylene and constitutes the first part of a more ambitious project that also includes the development of a modeling strategy of the processing behavior for short-fiber composites. [source]