			Home About us Contact

Primary Implant Stability (primary + implant_stability)

Distribution by Scientific Domains

Medical Sciences	100%

Selected Abstracts

Implant stability during osseointegration in irradiated and non-irradiated minipig alveolar bone: an experimental study

CLINICAL ORAL IMPLANTS RESEARCH, Issue 2 2008
Henk W. D. Verdonck
Abstract: Objectives: Primary implant stability is related to local bone density. After insertion of an implant, implant stability is subject to changes due to bone remodeling. In patients who have undergone radiotherapy in the head and neck region, implant stability is impaired because irradiation reduces bone vitality. The current study was designed to monitor and test implant stability immediately after implant placement and during osseointegration in irradiated and non-irradiated minipig alveolar bone. Materials and methods: All maxillary and mandibular premolars and molars of six adult Göttingen minipigs were extracted. The maxilla and mandible of three minipigs received three irradiation exposures at a total dose of 24 Gy. After irradiation, five initial implant holes were drilled in the residual alveolar ridge of each edentulous site. In order to assess bone vascularity, laser Doppler flowmetry recordings were carried out in the initial holes. A total of 120 implants were placed in the six minipigs. Subsequently, and at 8, 16, and 24 weeks after implant placement, implant stability was recorded by resonance frequency analysis (RFA). RFA values were expressed as an implant stability quotient (ISQ). Results: ISQ values recorded immediately after implant placement showed no differences between irradiated and non-irradiated minipigs. Repeated measurements at the four recording moments showed a decrease of ISQ values in all minipigs, being more pronounced in irradiated bone, when compared with non-irradiated bone. The results at the third and fourth recording moments showed a stabilization or even a slight increase of ISQ values. Conclusions: The results document the negative effect of irradiation on bone vascularity and hence on implant stability. [source]

Positive effect of early loading on implant stability in the bi-cortical guinea-pig model

CLINICAL ORAL IMPLANTS RESEARCH, Issue 4 2005
Els De Smet
Abstract: Loading, early after implant placement, has gained rapid interest in dentistry. Primary implant stability, as e.g. defined by resonance frequency instrumentation, has been isolated as a predicator when immediate and early implant loading is applied. The aim of this study was to investigate the effect of early (after 7 days) mechanical loading on the establishment of osseointegration by means of resonance frequency analysis (RFA). Percutaneous titanium implants were installed in both tibiae of 10 guinea-pigs. One week after implant installation, one implant (test) was loaded daily for 6 weeks, while the contra-lateral served as the unloaded one (control). A sinusoidally varying bending moment was applied at a frequency of 3 Hz and a force amplitude of 5 N, for 1800 cycli. Resonance frequency was measured at implant installation and from then on weekly using the RFA-device (Osstell®). Contrary to control implants, that showed a decrease in stability 1 week after installation, reaching a minimum at 3 weeks (,200 Hz), test implants showed a progressive increase in stability over time. After 6 weeks, the mean resonance frequency of test and control implants reached the same values. As confirmed by recent literature, early loading does not have to endanger the establishment of osseointegration of titanium implants. On the contrary, controlled loading is beneficial to maintain the implant stability during the early critical healing period as determined by RFA-measurements. Résumé La mise en charge précoce après l'insertion de l'implant acquière beaucoup d'intérêt en médecine dentaire. La stabilité primaire de l'implant, qui est par exemple définie par l'instrumentation de fréquence de résonnance RFA, a été isolée comme un annonciateur lorsque la mise en charge de l'implant était précoce ou immédiate. Le but de cette étude a été d'étudier l'effet d'une mise en charge précoce (sept jours) sur l'établissement de l'ostéïntégration à l'aide de RFA (Osstell®). Des implants titane percutanés ont été insérés dans les deux tibias de dix cobayes. Une semaine après le placement des implants, un implant test a été mis en charge tous les jours pendant six semaines tandis que le contralatéral servait de contrôle et n'était pas mis en charge. Un moment sinusoïdal a été appliquéà une fréquence de trois hertz et une amplitute d'une force de 5 N pour 1 800 cycles. La fréquence de résonnance a été mesurée lors de l'insertion de l'implant et ensuite hebdomadairement en utilisant le RFA. Contrairement aux implants contrôles, qui accusaient une diminution de la stabilité une semaine après leur insertion atteignant un minimum après trois semaines (,200 Hz), les implants tests ont montré une augmentation progressive de la stabilité avec le temps. Après six semaines, la fréquence de résonnance moyenne des implants tests et contrôles atteignaient les mêmes valeurs. Comme décrit dans la littérature récente, la mise en charge précoce ne met pas en danger l'établissement de l'ostéoïntégration des implants en titane. Au contraire, une mise en charge contrôlée est bénéfique au maintien de la stabilité implantaire durant la période de guérison critique précoce comme déterminée par les mesures RFA. Zusammenfassung Die Belastung kurz nach der Implantatplatzierung hat in der Zahnmedizin schnell an Interesse gewonnen. Die Primärstabilität der Implantate, bestimmt z.B. durch Messung der Resonanzfrequenz, hat sich als Voraussagewert herauskristallisiert, wenn eine Sofort-oder Frühbelastung der Implantate durchgeführt wird. Das Ziel dieser Studie war, den Einfluss der frühen (nach 7 Tagen) mechanischen Belastung auf die Ausbildung der Osseointegration mittels Resonanzfrequenzanalyse (RFA) zu untersuchen. In die beiden Tibias von 10 Meerschweinchen wurden perkutane Titanimplantate eingesetzt. Eine Woche nach der Implantation wurde ein Implantat (Test) während 6 Wochen täglich belastet, während das kontralaterale Implantat unbelastet blieb (Kontrolle). Es wurde ein Biegemoment mit sinusoidalen Schwankungen mit einer Frequenz von 3 Hz und einer Kraftamplitude von 5 N in 1800 Zyklen appliziert. Die Resonanzfrequenz wurde nach der Implantation und dann wöchentlich mit einem RFA-Gerät (Osstell®) gemessen. Im Gegensatz zu den Kontrollimplantaten, welche eine Woche nach dem Setzen eine Stabilitätsabnahme zeigten und das Minimum nach drei Wochen (,200 Hz) erreichten, konnte bei den Testimplantaten eine progressive Zunahme der Stabilität über die Zeit beobachtet werden. Nach sechs Wochen erreichten die mittleren Resonanzfrequenzen der Test-und Kontrollimplantate dieselben Werte. Die frühe Belastung gefährdet die Ausbildung einer Osseointegration bei Titanimplantaten nicht, was auch durch die neuere Literatur bestätig wird. Im Gegenteil, eine kontrollierte Belastung ist von Vorteil für den Erhalt der Implantatstabilität während der kritischen frühen Einheilphase. Dies konnte mittels RFA Messungen ermittelt werden. Resumen La carga temprana tras la colocación del implante ha ganado rápidamente interesen odontología. Se ha aislado como predictor, la estabilidad primaria del implante, definida por instrumentación de frecuencia de resonancia, cuando se aplica la carga temprana al implante. La intención del estudio fue investigar el efecto de carga mecánica temprana (tras 7 días) en el establecimiento de la osteointegración por medio del análisis de la frecuencia de resonancia (RFA). Se instalaron implantes de titanio percutaneos en ambas tibias de 10 conejos de indias. Una semana tras la instalación, un implante (prueba) se cargó diariamente durante 6 semanas, mientras que el contralateral sirvió como el implante sin carga (control). Se aplicó un momento de flexión variante sinusoidalmente a una frecuencia de 3 Hz y una amplitud de la fuerza de 5 N, durante 1899 ciclos. Se midió la frecuencia de resonancia al instalar el implante y a partir de ahí semanalmente usando el dispositivo RFA (Ostell®). Contrariamente a los implantes de control, que mostraron una disminución de la estabilidad una semana después de la instalación, alcanzando un mínimo a las tres semanas (,200 Hz), los implantes de prueba mostraron un incremento progresivo de la estabilidad a lo largo del tiempo. Tras seis semanas, la frecuencia de resonancia de los implantes de prueba y de control alcanzaron los mismos valores. Tal como se confirma por la literatura reciente, la carga temprana no debe hacer peligrar el establecimiento de la osteointegración de los implantes de titanio. Por lo contrario, la carga controlada es beneficiosa para mantener la estabilidad de los implantes durante el periodo crítico de la cicatrización determinado por las mediciones de RFA. [source]

Early Complete Failures of Fixed Implant-Supported Prostheses in the Edentulous Maxilla: A 3-Year Analysis of 17 Consecutive Cluster Failure Patients

CLINICAL IMPLANT DENTISTRY AND RELATED RESEARCH, Issue 2 2006
Odont Dr/PhD, Torsten Jemt DDS
ABSTRACT Background, Clusters of implant failures in the edentulous maxilla seem to occur in some patients. To create groups for analysis with higher numbers of these patients implies large original groups for inclusion. Purpose, The aim of this study was to retrospectively describe and compare a group of "cluster failure patients" with randomly selected patients treated in the edentulous maxilla. Materials and Methods, From a group of 1,267 consecutively treated patients in one clinic, all patients presenting failing fixed implant-supported prostheses within the first 3 years of follow-up were included. All patients were treated with turned titanium implants using two-stage surgery. A control group of equal number of patients were created for comparison. Data on patients were retrospectively retrieved from their records, and compared. Results, Seventeen patients (1.3%) met the inclusion criteria in the entire group. The bone resorption index revealed less bone quantity in the study group (p < .05) during implant placement, but there was no difference regarding primary implant stability at first-stage surgery. The distribution of short and long implants showed relatively higher number of short implants in the study group (p < .05), and more patients had a presurgical discussion on the risk of implant failure prior to treatment in this group (p < .05). Only 5 out of 102 implants (4.9%) were lost before prosthesis placement as compared to 38 and 25 lost implants during the following two years in the study group. Smoking habits and signs of bone loss related to periodontitis in the lower dentition were more frequent in the study group, but did not reach a significant level (p > .05). Conclusion, The results indicate that bone quantity, reflected in fixture length, has a significant impact on increased implant failure risk. Other factors of interest as predictors for implant failures could be smoking habits and also possibly signs of periodontitis in the opposing dentition. [source]

Influence of surgical technique and surface roughness on the primary stability of an implant in artificial bone with different cortical thickness: a laboratory study

CLINICAL ORAL IMPLANTS RESEARCH, Issue 2 2010
Afsheen Tabassum
Abstract Objective: The aim of this biomechanical study was to assess the interrelated effect of both surface roughness and surgical technique on the primary stability of dental implants. Material and methods: For the experiment, 160 screw-designed implants (Biocomp®), with either a machined or an etched surface topography, were inserted into polyurethane foam blocks (Sawbones®). As an equivalent of trabecular bone, a density of 0.48 g/cm3 was chosen. To mimic the cortical layer, on top of these blocks short-fibre-filled epoxy sheets were attached with a thickness varying from 0 to 2.5 mm. The implant sites were prepared using either a press-fit or an undersized technique. To measure the primary stability of the implant, both the insertion and the removal torques were scored. Results: Independent of the surgical technique used, both implant types showed an increased insertion and removal torque values with increasing cortical thickness, although >2 mm cortical layer no further increase in insertion torque was observed. In the models with only trabecular bone (without cortical layer) and with a 1 mm cortical layer, both implant types showed a statistically higher insertion and removal torque values for undersized compared with the press-fit technique. In addition, etched implants showed a statistically higher insertion and removal torque mean values compared with machined implants. In the models with 2 and 2.5 mm cortical layers, with respect to the insertion torque values, no effect of either implantation technique or implant surface topography could be observed. Conclusion: The placement of etched implants in synthetic bone models using an undersized preparation technique resulted in enhanced primary implant stability. A correlation was found between the primary stability and the cortical thickness. However, at or above a cortical thickness of 2 mm, the effect of both an undersized surgical approach, as also the presence of a roughened (etched) implant surface, had no extra effect. Besides the mechanical aspects, the biological effect of undersized drilling, i.e. the bone response on the extra insertion torque forces should also be elucidated. Therefore, additional in vivo studies are needed. To cite this article: Tabassum A, Meijer GJ, Wolke JGC, Jansen JA. Influence of surgical technique and surface roughness on the primary stability of an implant in artificial bone with different cortical thickness: a laboratory study. Clin. Oral Impl. Res. 21, 2010; 213,220. doi: 10.1111/j.1600-0501.2009.01823.x [source]

Significance of primary stability for osseointegration of dental implants

CLINICAL ORAL IMPLANTS RESEARCH, Issue 3 2006
Natalia Lioubavina-Hack
Abstract Aim: To investigate the significance of the initial stability of dental implants for the establishment of osseointegration in an experimental capsule model for bone augmentation. Material and methods: Sixteen male rats were used in the study. In each rat, muscle-periosteal flaps were elevated on the lateral aspect of the mandibular ramus on both sides, resulting in exposure of the bone surface. Small perforations were then produced in the ramus. A rigid, hemispherical Teflon® capsule with a diameter of 6 mm and a height of 4 mm and with a hole in its middle portion, prepared to fit the circumference of an ITI® HC titanium implant of 2.8 mm in diameter, was fixed to the ramus using 4 mini-screws. On one side of the jaw, the implant was placed through the hole in such a way that its apex did not make contact with the mandibular ramus (test). This placement of the implant did not ensure primary stability. On the other side of the jaw, a similar implant was placed through the hole of the capsule in such a way that contact was made between the implant and the surface of the ramus (control). This provided primary stability of the implant. After placement of the implants, the soft tissues were repositioned over the capsules and sutured. After 1, 3, 6 and 9 months, four animals were sacrificed and subjected to histometric analysis. Results: The mean height of direct bone-to-implant contact of implants with primary stability was 38.8%, 52.9%, 64.6% and 81.3% of the implant length at 1, 3, 6 and 9 months, respectively. Of the bone adjacent to the implant surface, 28.1%, 28.9%, 52.6% and 69.6%, respectively, consisted of mineralized bone. At the test implants, no bone-to-implant contact was observed at any observation time or in any of these non-stabilized specimens. Conclusion: The findings of the present study indicate that primary implant stability is a prerequisite for successful osseointegration, and that implant instability results in fibrous encapsulation, thus confirming previously made clinical observations. [source]