Home About us Contact
|
Home About us Contact | ||
|
|
||
Pipe System (pipe + system)
Selected AbstractsFlashing characteristics in a pipe downstream from a depressurizing tank and temperature fluctuation characteristics at a mixing tee junction with cold water injectionHEAT TRANSFER - ASIAN RESEARCH (FORMERLY HEAT TRANSFER-JAPANESE RESEARCH), Issue 5 2003Koji Shiina Abstract The flashing characteristics in a pipe downstream from a depressurizing tank were experimentally and analytically investigated on the basis of the transient test and two-phase flow analysis. The following conclusions were obtained. (1) When the pressure margin of the pump inlet side and the distance to obtain an isothermal condition were sufficient, flashing phenomena did not occur in spite of the decreasing pressure. (2) When the ratio of the cold water injection flow rate to the hot water flow rate Mc/Mh increased, the peak distance of the water temperature fluctuation moved from L/D = 1 to 0, and the maximum water temperature fluctuation ratio was about 40% of the temperature difference between hot and cold water near the mixing tee junction. Because no problem occurred regarding the pipe material thermal fatigue, reliability of the mixing tee junction was assured. (3) Due to suppression of flashing phenomena of the mixing pipe system, the decision diagram on the flashing occurrence was obtained from the test and the analytical results, taking into consideration three factors: the depressurizing ratio in the tank; the cold water injection flow rate due to remaining subcooling; and the delay time of thermal mixing. The simplified analytical equation was used to decrease the cold water injection flow rate by the optimized pipe length between the mixing tee junction and the drain pump. The cold water injection flow rate was minimized when the pipe length was about 15 to 20 times the pipe inner diameter. © 2003 Wiley Periodicals, Inc. Heat Trans Asian Res, 32(5): 411,429, 2003; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/htj.10096 [source] Fuzzy controlled central heating systemINTERNATIONAL JOURNAL OF ENERGY RESEARCH, Issue 15 2002Faruk Mendi Abstract In this paper a comparison study was carried out in order to understand how two different systems, classical and fuzzy logic control of central heating affect the economy and comfort of private homes or offices. Also a literature review was done to help decide which one of these systems is more effective. The objective of the fuzzy controller heating system is to estimate the actual heat requirement of the house. It uses a total of five inputs, four of which are derived from energy consumption curve, using conventional digital filtering techniques; the fifth is the average outdoor temperature, whereas, the classical control system burns diesel type fuel in its furnace to heat the water supply (boiler). From the boiler, the hot water is distributed by a pipe system to the individual radiators in the house. Thereby, it is shown that the fuzzy controlled heating system is more effective, also it maximizes the economy and the comfort of the consumer. Copyright © 2002 John Wiley & Sons, Ltd. [source] The effect of inlet subcooling on two-phase flow instabilities in a horizontal pipe system with augmented surfacesINTERNATIONAL JOURNAL OF ENERGY RESEARCH, Issue 2 2002lmaz Abstract This research has been conducted to investigate the effect of inlet subcooling on two-phase flow instabilities in a horizontal pipe system with augmented surfaces. Five different inlet temperatures are used to study the effect of inlet subcooling for five different heat transfer surface configurations. All experiments are carried out at constant heat input, system pressure and exit restriction. The effect of inlet subcooling on the steady-state characteristics and two-phase flow instabilities are studied for each configuration. The bound aries for the appearance of pressure-drop-type and density-wave-type instabilities are found and the effect of the inlet subcooling on these oscillations is studied for each configuration. Copyright © 2002 John Wiley & Sons, Ltd. [source] Hydrological connectivity of soil pipes determined by ground-penetrating radar tracer detectionEARTH SURFACE PROCESSES AND LANDFORMS, Issue 4 2004Joseph Holden Abstract Soil pipes are common and important features of many catchments, particularly in semi-arid and humid areas, and can contribute a large proportion of runoff to river systems. They may also signi,cantly in,uence catchment sediment and solute yield. However, there are often problems in ,nding and de,ning soil pipe networks which are located deep below the surface. Ground-penetrating radar (GPR) has been used for non-destructive identi,cation and mapping of soil pipes in blanket peat catchments. While GPR can identify subsurface cavities, it cannot alone determine hydrological connectivity between one cavity and another. This paper presents results from an experiment to test the ability of GPR to establish hydrological connectivity between pipes through use of a tracer solution. Sodium chloride was injected into pipe cavities previously detected by the radar. The GPR was placed downslope of the injection points and positioned on the ground directly above detected soil pipes. The resultant radargrams showed signi,cant changes in re,ectance from some cavities and no change from others. Pipe waters were sampled in order to check the radar results. Changes in electrical conductivity of the pipe water could be detected by the GPR, without data post-processing, when background levels were increased by more than approximately twofold. It was thus possible to rapidly determine hydrological connectivity of soil pipes within dense pipe networks across hillslopes without ground disturbance. It was also possible to remotely measure travel times through pipe systems; the passing of the salt wave below the GPR produced an easily detectable signal on the radargram which required no post-processing. The technique should allow remote sensing of water sources and sinks for soil pipes below the surface. The improved understanding of ,owpath connectivity will be important for understanding water delivery, solutional and particulate denudation, and hydrological and geomorphological model development. Copyright © 2004 John Wiley & Sons, Ltd. [source] Interaction between phosphorus and biodegradable organic carbon on drinking water biofilm subject to chlorinationJOURNAL OF APPLIED MICROBIOLOGY, Issue 6 2010S.-K. Park Abstract Aims:, To examine whether phosphorus and biodegradable organic carbon interact to impact biofilm density and physiological function of biofilm-forming bacteria under conditions relevant to chlorinated drinking water distribution systems. Materials and Results:, The 2 × 2 factorial experiments with low and high levels of phosphorus and biodegradable organic carbon were performed on 4 -week-old drinking water biofilms in four separate pipe systems in the presence of chlorine. Experimental results revealed that biofilm heterotrophic plate count levels increased with the increase in biodegradable organic carbon concentration, showed no response to increases in levels of phosphorus and was not affected by interaction between phosphorus and biodegradable organic carbon. However, a significant positive interaction between phosphorus and biodegradable organic carbon was found to exist on biofilm mass and physiological function and/or metabolic potentials of biofilm communities; the effects of biodegradable organic carbon on biofilm mass and physiological function of biofilm-forming bacteria were accelerated in going from low to high level of phosphorus. Conclusions:, Biodegradable organic carbon was found to be the primary nutrient in regulating biofilm formation in drinking water regardless of the presence of chlorine. It can be therefore concluded that the removal of an easily biodegradable organic carbon is necessary to minimize the biofilm growth potential induced by the intrusion of phosphorus. Significance and Impact of the Study:, Phosphorus introduced to drinking water may interact with biodegradable organic carbon, thus leading to measurable impact on the biofilm formation. [source] | ||||||||||