Home About us Contact
|
Home About us Contact | ||
|
|
||
Orthopedic Applications (orthopedic + application)
Selected AbstractsNovel Rice-shaped Bioactive Ceramic Nanoparticles (Adv. Eng.ADVANCED ENGINEERING MATERIALS, Issue 5 2009Mater. The cover of Advanced Biomaterials shows Rice-shaped bioactive ceramic nanoparticles with 70 nm in average diameter and around 200 nm in length were produced by an improved sol-gel method. In comparison to most traditional bioactive glass/ceramic materials this novel bioactive ceramic contains a significant lower quantity of silicon and higher content of phosphorous. In vitro bioactivity test showed that this new class of materials can induce the deposition of an apatite layer from SBF solution, having potential to be used in both conventional orthopedic applications or in bone tissue engineering when incorporated in composite scaffolds. More information can be found in the article of J. F. Mano et al. on page B25. [source] Novel Rice-shaped Bioactive Ceramic Nanoparticles,ADVANCED ENGINEERING MATERIALS, Issue 5 2009Zhongkui Hong Rice-shaped bioactive ceramic nanoparticles of 70 nm average diameter and around 200 nm length were produced by an improved sol-gel method. In comparison to most traditional bioactive glass/ceramic materials, this novel bioactive ceramic contains a significant lower quantity of silicon and higher content of phosphorous. In vitro bioactivity tests showed that this new class of materials can induce the deposition of an apatite layer from simulated body fluid, having the potential to be used in both conventional orthopedic applications or in bone tissue engineering when incorporated in composite scaffolds. [source] Analysis of the mechanical behavior of a titanium scaffold with a repeating unit-cell substructureJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 2 2009Garrett Ryan Abstract Titanium scaffolds with controlled microarchitecture have been developed for load bearing orthopedic applications. The controlled microarchitecture refers to a repeating array of unit-cells, composed of sintered titanium powder, which make up the scaffold structure. The objective of this current research was to characterize the mechanical performance of three scaffolds with increasing porosity, using finite element analysis (FEA) and to compare the results with experimental data. Scaffolds were scanned using microcomputed tomography and FEA models were generated from the resulting computer models. Macroscale and unit-cell models of the scaffolds were created. The material properties of the sintered titanium powders were first evaluated in mechanical tests and the data used in the FEA. The macroscale and unit-cell FEA models proved to be a good predictor of Young's modulus and yield strength. Although macroscale models showed similar failure patterns and an expected trend in UCS, strain at UCS did not compare well with experimental data. Since a rapid prototyping method was used to create the scaffolds, the original CAD geometries of the scaffold were also evaluated using FEA but they did not reflect the mechanical properties of the physical scaffolds. This indicates that at present, determining the actual geometry of the scaffold through computed tomography imaging is important. Finally, a fatigue analysis was performed on the scaffold to simulate the loading conditions it would experience as a spinal interbody fusion device. © 2009 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 2009 [source] Lyophilization to improve drug delivery for chitosan-calcium phosphate bone scaffold construct: A preliminary investigationJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 1 2009Benjamin T. Reves Abstract Lyophilization was evaluated in chitosan-calcium phosphate microspheres and scaffolds to improve drug delivery of growth factors and antibiotics for orthopedic applications. The dual delivery of an antibiotic and a growth factor from a composite scaffold would be beneficial for treatment of complex fracture sites, such as comminuted fractures and segmental bone defects. The aim of this investigation was to increase the loading capacity of the composite by taking advantage of the increased porosity, due to lyophilization, and to produce an extended elution profile using a secondary chitosan-bead coating. The physiochemical properties of the composite were investigated, and loading and elution studies were performed with alkaline phosphatase (ALP), bone morphogenetic protein-2 (BMP-2), and amikacin. Lyophilization was found to increase the surface area of scaffolds by over 400% and the porosity of scaffolds by 50%. Using ALP as a model protein, the loading capacity was increased by lyophilization from 4.3 ± 2.5 to 24.6 ± 3.6 ,g ALP/mg microspheres, and the elution profile was extended by a supplemental chitosan coating. The loading capacity of BMP-2 for composite microspheres was increased from 74.4 ± 3.7 to 102.1 ± 8.0 ,g BMP-2/g microspheres with lyophilization compared with nonlyophilized microspheres. The elution profiles of BMP-2 and the antibiotic amikacin were not extended with the supplemental coating. Additional investigations are planned to improve these elution characteristics for growth factors and antibiotics. © 2009 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2009 [source] Controlling the biodegradation rate of magnesium using biomimetic apatite coatingJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 2 2009Yajing Zhang Abstract Magnesium is light, biocompatible and has similar mechanical properties to natural bone, so it has the potential to be used as a biodegradable material for orthopedic applications. However, pure magnesium severely corrodes in a physiological environment, which may result in fracture prior to substantial tissue healing. Hydroxyapatite (HA) is the main composition of natural bone. It has excellent bioactivity and osteoconductivity. In this study, HA coating with two different thicknesses was applied onto the surface of pure magnesium substrates using a biomimetic technique. The corrosion rate of the surface-treated substrates was tested. It was found that both types of coatings substantially slowed down the corrosion of the substrate, and the dual coating was more effective than the single coating in hindering the degradation of the substrate. Thus, the corrosion rate of magnesium implants can be closely tailored by adjusting apatite coating thickness and thereby monitoring the release of magnesium ions into the body. © 2008 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2009 [source] Aqueous Colloidal Processing of ZTA CompositesJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 1 2009Susana M. Olhero Two different zirconia-alumina composites, ZTA-30 (70 wt% Al2O3+30 wt% ZrO2) and ZTA-60 (40 wt% Al2O3+60 wt% ZrO2), with potential for orthopedic applications, were processed in aqueous media and consolidated by slip casting (SC), hydrolysis-assisted solidification (HAS), and gelcasting (GC) from suspensions containing 50 vol% solids loading. For comparison purposes, the same ceramic compositions were also consolidated by die pressing of freeze-dried granules (FG). In the HAS process, 5 wt% of Al2O3 in the precursor mixture was replaced by equivalent amounts of AlN to promote the consolidation of the suspensions. Ceramics consolidated via GC exhibited higher green (three-point bend) strengths (,17 MPa) than those consolidated by other techniques. Further, these ceramics also exhibited superior fracture toughness and flexural strength properties after sintering for 1 h at 1600°C in comparison with those consolidated by other techniques, including conventional die pressing (FG). [source] | ||||||||||