Home About us Contact
|
Home About us Contact | ||
|
|
||
Monolithic Column (monolithic + column)
Selected AbstractsLiquid Chromatography of Synthetic Polymers under Limiting Conditions of Insolubility IIIMACROMOLECULAR SYMPOSIA, Issue 1 2007Application of Monolithic Columns Abstract Summary Performance was evaluated of silica based commercial monolithic rod-like columns in liquid chromatography of synthetic polymers under limiting conditions of enthalpic interactions (LC LC). LC LC employs the barrier effect of the pore permeating and therefore slowly eluting small molecules toward the pore excluded, fast eluting macromolecules. Phase separation (precipitation) barrier action was applied in present study. The barrier was created either by the narrow pulse of an appropriate nonsolvent injected into the column just before the sample solution (LC LC of insolubility , LC LCI) or by the eluent itself. In the latter case, the polymer sample was dissolved and injected in a good solvent (LC LC of solubility , LC LCS). In LC LCI, polymer species cannot break thru the nonsolvent zone while in LC LCS they cannot enter eluent, which is their precipitant. Therefore, polymer species keep moving in the zone of their original solvent. Macromolecules eluting under the LC LC mechanism leave the column in the retention volume (VR) roughly corresponding to VR of the low molar mass substances and can be efficiently separated from the polymer species non-hindered by the barrier action. The known advantages of monoliths were confirmed. From the point of view of LC LCI and LC LCS the most important quality of monolithic columns represents their excellent permeability, which allows both working at high flow rates and injecting very high (in the range of 5%) sample concentrations. Monolithic column tolerate also extremely high molar mass samples (M>10,000 kg,·,mol,1). On the other hand, the mesopores (separation pores) of the tested monoliths exhibited rather small volume and wide size distribution. These shortcomings partially impair the permeability advantage of monoliths because in order to obtain high LC LC separation selectivity a tandem of several monolithic columns must be applied. Presence of large mesopores also reduces applicability of monolithic columns for molar masses below about 50 kg,·,mol,1 because VRs of polymers eluted behind the barrier are similar to that of freely eluting species. The non- negligible break-thru phenomenon was observed for the very high polymer molar masses largely eluting behind the barrier. It is assumed that the fraction of very large mesopores present in the monoliths or association/microphase separation of macromolecules may be responsible for this phenomenon. This is why the presently marketed SiO2 monolithic columns are mainly suitable for the fast purification of the LC LC eluting macromolecules from the polymeric admixtures non-hindered by the barrier-forming liquid. Still, monolithic columns have large potential in the LC LCI and LC LCS procedures provided size (effective diameter) of the mesopores can be reduced and their volume increased. [source] Preparation and evaluation of the highly cross-linked poly(1-hexadecane-co-trimethylolpropane trimethacrylate) monolithic column for capillary electrochromatographyELECTROPHORESIS, Issue 20 2009Minghua Lu Abstract In this paper, a novel highly cross-linked porous monolithic stationary phase having a long alkyl chain ligand (C16) was introduced and evaluated in CEC. The monolithic stationary phase was prepared by in situ copolymerization of 1-hexadecene, trimethylolpropane trimethacrylate, and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) in the presence of ternary porogenic solvent (cyclohexanol/1,4-butanediol/water). In preparing monoliths, the ternary cross-linker trimethylolpropane trimethacrylate was usually applied to preparing molecularly imprinted polymers or molecularly imprinted solid-phase extraction, instead of binary cross-linker ethylene dimethacrylate. 1-Hexadecene was introduced to provide the non-polar sites (C16) for chromatographic retention, while AMPS was used to generate the EOF for transporting the mobile phase through the monolithic capillary. Monolithic columns were prepared by optimizing proportion of porogenic solvent and AMPS content in the polymerization solution as well as the cross-linkers. The monolithic stationary phases could generate a strong and stable EOF in various pH values and exhibit an RP-chromatographic behavior for neutral compounds. For charged compounds, the separation was mainly based on the association of hydrophobic, electrostatic and electrophoretic interaction. [source] High-efficiency peptide analysis on monolithic multimode capillary columns: Pressure-assisted capillary electrochromatography/capillary electrophoresis coupled to UV and electrospray ionization-mass spectrometryELECTROPHORESIS, Issue 21 2003Alexander R. Ivanov Abstract High-efficiency peptide analysis using multimode pressure-assisted capillary electrochromatography/capillary electrophoresis (pCEC/pCE) monolithic polymeric columns and the separation of model peptide mixtures and protein digests by isocratic and gradient elution under an applied electric field with UV and electrospray ionization-mass spectrometry (ESI-MS) detection is demonstrated. Capillary multipurpose columns were prepared in silanized fused-silica capillaries of 50, 75, and 100 ,m inner diameters by thermally induced in situ copolymerization of methacrylic monomers in the presence of n -propanol and formamide as porogens and azobisisobutyronitrile as initiator. N -Ethylbutylamine was used to modify the chromatographic surface of the monolith from neutral to cationic. Monolithic columns were termed as multipurpose or multimode columns because they showed mixed modes of separation mechanisms under different conditions. Anion-exchange separation ability in the liquid chromatography (LC) mode can be determined by the cationic chromatographic surface of the monolith. At acidic pH and high voltage across the column, the monolithic stationary phase provided conditions for predominantly capillary electrophoretic migration of peptides. At basic pH and electric field across the column, enhanced chromatographic retention of peptides on monolithic capillary column made CEC mechanisms of migration responsible for separation. The role of pressure, ionic strength, pH, and organic content of the mobile phase on chromatographic performance was investigated. High efficiencies (exceeding 300,000 plates/m) of the monolithic columns for peptide separations are shown using volatile and nonvolatile, acidic and basic buffers. Good reproducibility and robustness of isocratic and gradient elution pressure-assisted CEC/CE separations were achieved for both UV and ESI-MS detection. Manipulation of the electric field and gradient conditions allowed high-throughput analysis of complex peptide mixtures. A simple design of sheathless electrospray emitter provided effective and robust low dead volume interfacing of monolithic multimode columns with ESI-MS. Gradient elution pressure-assisted mixed-mode separation CE/CEC-ESI-MS mass fingerprinting and data-dependent pCE/pCEC-ESI-MS/MS analysis of a bovine serum albumin (BSA) tryptic digest in less than 5 min yielding high sequence coverage (73%) demonstrated the potential of the method. [source] Preparation and characterization of polymethacrylate monolithic capillary columns with dual hydrophilic interaction reversed-phase retention mechanism for polar compoundsJOURNAL OF SEPARATION SCIENCE, JSS, Issue 15-16 2009í Urban Abstract Monolithic columns for capillary hydrophilic interaction liquid chromatography (HILIC) were prepared in fused-silica capillaries by radical co-polymerization of [2-(methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl)ammonium hydroxide and ethylene dimethacrylate in various binary and ternary porogen solvent mixtures with azobisisobutyronitrile as the initiator of the polymerization reaction. Columns showed mixed separation modes: reversed-phase (RP) in water-rich mobile phases and HILIC at high concentrations of acetonitrile (>60,80%) in aqueous,organic mobile phases. A continuous change in retention was observed at increasing concentration of water in acetonitrile, giving rise to characteristic U-turn plots of retention factors versus the concentration of water in the mobile phase, with minima corresponding to the transition between the mechanisms controlling the retention. The selectivity of organic polymer monolithic columns for HILIC separations can be varied by adjusting the concentration of sulfobetaine monomer and the composition of the porogen solvent in the polymerization mixture. Under HILIC conditions, the monolithic capillary sulfobetaine columns show separation selectivities for polar phenolic acids similar to those of a commercial silica-based sulfobetaine ZIC-HILIC column, which, however, has limited selectivity in the RP mode due to lower retention. [source] Spherical ordered mesoporous silicas and silica monoliths as stationary phases for liquid chromatographyJOURNAL OF SEPARATION SCIENCE, JSS, Issue 6 2006Anne Galarneau Abstract Ordered mesoporous silicas such as micelle-templated silicas (MTS) feature unique textural properties in addition to their high surface area (,1000 m2/g): narrow mesopore size distributions and controlled pore connectivity. These characteristics are highly relevant to chromatographic applications for resistance to mass transfer, which has never been studied in chromatography because of the absence of model materials such as MTS. Their synthesis is based on unique self-assembly processes between surfactants and silica. In order to take advantage of the perfectly adjustable texture of MTS in chromatographic applications, their particle morphology has to be tailored at the micrometer scale. We developed a synthesis strategy to control the particle morphology of MTS using the concept of pseudomorphic transformation. Pseudomorphism was recognized in the mineral world to gain a mineral that presents a morphology not related to its crystallographic symmetry group. Pseudomorphic transformations have been applied to amorphous spherical silica particles usually used in chromatography as stationary phases to produce MTS with the same morphology, using alkaline solution to dissolve progressively and locally silica and reprecipitate it around surfactant micelles into ordered MTS structures. Spherical beads of MTS with hexagonal and cubic symmetries have been synthesized and successfully used in HPLC in fast separation processes. MTS with a highly connected structure (cubic symmetry), uniform pores with a diameter larger than 6 nm in the form of particles of 5 ,m could compete with monolithic silica columns. Monolithic columns are receiving strong interest and represent a milestone in the area of fast separation. Their synthesis is a sol-gel process based on phase separation between silica and water, which is assisted by the presence of polymers. The control of the synthesis of monolithic silica has been systematically explored. Because of unresolved yet cladding problems to evaluate the resulting macromonoliths in HPLC, micromonoliths were synthesized into fused-silica capillaries and evaluated by nano-LC and CEC. Only CEC allows to gain high column efficiencies in fast separation processes. Capillary silica monolithic columns represent attractive alternatives for miniaturization processes (lab-on-a chip) using CEC. [source] Direct analysis of pharmaceutical compounds in human plasma with chromatographic resolution using an alkyl-bonded silica rod columnRAPID COMMUNICATIONS IN MASS SPECTROMETRY, Issue 12 2001Robert Plumb Monolithic columns have been successfully used with steep gradient and high flow rates for the direct analysis of a candidate pharmaceutical compound in human plasma. The monolithic columns showed excellent robustness with nearly 300 20-µL injections of plasma (diluted 1:1 with water) being made onto one column without significant deterioration in performance. The system gave excellent sensitivity with a limit of quantification of 5,ng/mL being achieved. Unlike previous methods of direct analysis the monolithic columns showed excellent resolution even after nearly 300 plasma injections. The column performance was measured before and after the analysis of the plasma samples. Copyright © 2001 John Wiley & Sons, Ltd. [source] Assay of vitamin B in urine by capillary electrochromatography with methacrylate-based monolithic columnELECTROPHORESIS, Issue 19 2010Xiaoyi Wei Abstract A novel and simple method for the separation of major vitamin B analytes, such as thiamine, riboflavin, nicotinamide, vitamin B4, pyridoxine, has been developed by CEC using the monolithic column. It has been found that the baseline separation of the five analytes could be achieved with 5.0,mM phosphate buffer at pH 4.0. Compared with the open-tubular capillary and the bared capillary columns, the poly(butylmethacrylate-co-ethylene glycol dimethacrylate) monolithic capillary could exhibit the best resolution in the analysis. Then the method was validated and the linear calibration ranges were obtained with correlation coefficients more than 0.997. The precision and the recovery were also investigated and showed a good result. Furthermore, the proposed method was successfully applied to assay the concentration of vitamin B analytes and the metabolic situation in human urine samples. [source] Preparation and characterization of a molecularly imprinted monolithic column for pressure-assisted CEC separation of nitroimidazole drugsELECTROPHORESIS, Issue 16 2010Sulan Liao Abstract A polymethacrylate-based molecularly imprinted monolithic column bearing mixed functional monomers, using non-covalent imprinting approach, was designed for the rapid separation of nitroimidazole compounds. The new monolithic column has been prepared via simple in situ polymerization of 2-hydroxyethyl methacrylate, dimethylaminoethyl methacrylate and ethylene dimethacrylate, using (S)-ornidazole ((S)-ONZ) as template in a binary porogenic mixture consisting of toluene and dodecanol. The composition of the polymerization mixture was systematically altered and optimized by altering the amount of monomers as well as the composition of the porogenic solvent. The column performance was evaluated in pressure-assisted CEC mode. Separation conditions such as pH, voltage, amount of organic modifier and salt concentration were studied. The optimized monolithic column resulted in excellent separation of a group of structurally related nitroimidazole drugs within 10,min in isocratic elution condition. Column efficiencies of 99,000, 80,000, 103,000, 60,000 and 99,000,plates/m were obtained for metronidazole, secnidazole, ronidazole, tinidazole and dimetridazole, respectively. Parallel experiments were carried out using molecularly imprinted and non-imprinted capillary columns. The separation might be the result of combined effects including hydrophobic, hydrogen bonding and the imprinting cavities on the (S)-ONZ-imprinted monolithic column. [source] Preparation and evaluation of the highly cross-linked poly(1-hexadecane-co-trimethylolpropane trimethacrylate) monolithic column for capillary electrochromatographyELECTROPHORESIS, Issue 20 2009Minghua Lu Abstract In this paper, a novel highly cross-linked porous monolithic stationary phase having a long alkyl chain ligand (C16) was introduced and evaluated in CEC. The monolithic stationary phase was prepared by in situ copolymerization of 1-hexadecene, trimethylolpropane trimethacrylate, and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) in the presence of ternary porogenic solvent (cyclohexanol/1,4-butanediol/water). In preparing monoliths, the ternary cross-linker trimethylolpropane trimethacrylate was usually applied to preparing molecularly imprinted polymers or molecularly imprinted solid-phase extraction, instead of binary cross-linker ethylene dimethacrylate. 1-Hexadecene was introduced to provide the non-polar sites (C16) for chromatographic retention, while AMPS was used to generate the EOF for transporting the mobile phase through the monolithic capillary. Monolithic columns were prepared by optimizing proportion of porogenic solvent and AMPS content in the polymerization solution as well as the cross-linkers. The monolithic stationary phases could generate a strong and stable EOF in various pH values and exhibit an RP-chromatographic behavior for neutral compounds. For charged compounds, the separation was mainly based on the association of hydrophobic, electrostatic and electrophoretic interaction. [source] On-line preconcentration and enantioseparation of thalidomide racemates by CEC with the hyphenation of octyl and norvancomycin monolithsELECTROPHORESIS, Issue 4 2009An-Na Tang Abstract A method was developed for simultaneous preconcentration and chiral separation of thalidomide enantiomers in human urine by CEC in combination with self-concentration and solvent gradient effects. A 4,cm long octyl (C8) monolithic column was hyphenated with a 15,cm long norvancomycin (NVC)-bonded monolithic column via a fluorinated ethylene,propylene interface. Sample solution was injected into the C8 monolithic column, the two thalidomide enantiomers were first preconcentrated on the C8 monolithic column, and then separated with a further concentration on the NVC-bonded monolithic column by CEC. Injection of 34.8,mm plug of sample solution gave 278- and 298-fold enhancement in sensitivity, and detection limits of 90 and 94,,g/L for the two thalidomide enantiomers. Peak areas of the two isomers were linear in a range of 0.5,50,mg/L. The precision for five replicate injections of 10,mg/L were 0.8,0.9 and 1.1,2.3% for the migration time and peak height, respectively. The developed method was applied to the determination of racemic thalidomide in spiked human urine samples. [source] Methacrylate-based monolithic column with mixed-mode hydrophilic interaction/strong cation-exchange stationary phase for capillary liquid chromatography and pressure-assisted CECELECTROPHORESIS, Issue 19 2008Jian Lin Abstract A novel porous polymethacrylate-based monolithic column by in situ copolymerization of 3-sulfopropyl methacrylate (SPMA) and pentaerythritol triacrylate in a binary porogenic solvent consisting of cyclohexanol/ethylene glycol was prepared. The monolith possessed in their structures bonded sulfonate groups and hydroxyl groups and was evaluated as a hydrophilic interaction and strong cation-exchange stationary phases in capillary liquid chromatography (cLC) and pressure-assisted CEC using small polar neutral and charged solutes. While the SPMA was introduced as multifunctional monomer, the pentaerythritol triacrylate was used to replace ethylene glycol dimethacrylate as cross-linker with much more hydrophilicity due to a hydroxyl sub-layer. The different characterization of monolithic stationary phases were specially designed and easily prepared by altering the amount of SPMA in the polymerization solution as well as the composition of the porogenic solvent for cLC and pressure-assisted CEC. The resulting monolith showed the different trends about the effect of the permeabilities on efficiency in the pressure-assisted CEC and cLC modes. A typical hydrophilic interaction chromatography mechanism was observed at higher organic solvent content (ACN%>70%) for polar neutral analytes. For polar charged analytes, both hydrophilic interaction and electrostatic interaction contributed to their retention. Therefore, for charged analytes, selectivity can be readily manipulated by changing the composition of the mobile phase (e.g., pH, ionic strength and organic modifier). With the optimized monolithic column, high plate counts reaching greater than 170,000,plates/m for pressure-assisted CEC and 105,000 plates/m for cLC were easily obtained, respectively. [source] Macrocyclic polyamine-modified poly(glycidyl methacrylate- co -ethylene dimethacrylate) monolith for capillary electrochromatographyELECTROPHORESIS, Issue 11 2008Yun Tian Abstract 1,4,10,13,16-Pentaazatricycloheneicosane-9,17-dione (macrocyclic polyamine)-modified polymer-based monolithic column for CEC was prepared by ring opening reaction of epoxide groups from poly(glycidyl methacrylate- co -ethylene dimethacrylate) (GMA- co -EDMA) monolith with macrocyclic polyamine. Conditions such as reaction time and concentration of macrocyclic polyamine for the modification reaction were optimized to generate substantial EOF and enough chromatographic interactions. Anodic EOF was observed in the pH range of 2.0,8.0 studied due to the protonation of macrcyclic polyamine at the surface of the monolith. Morphology of the monolithic column was examined by SEM and the incorporation of macrocyclic polyamine to the poly(GMA- co -EDMA) monolith was characterized by infrared (IR) spectra. Successful separation of inorganic anions, isomeric benzenediols, and benzoic acid derivatives on the monolithic column was achieved for CEC. In addition to hydrophobic interaction, hydrogen bonding and electrostatic interaction played a significant role in the separation process. [source] Cover Picture: Electrophoresis 10/2008ELECTROPHORESIS, Issue 10 2008Article first published online: 21 MAY 200 Regular issues provide a wide range of research and review articles covering all aspects of electrophoresis. Here you will find cutting-edge articles on methods and theory, instrumentation, nucleic acids, CE and CEC, miniaturization and microfluidics, proteomics and two-dimensional electrophoresis. "The present issue includes 29 manuscripts subdivided into three major parts: one part is devoted to instrumental and methodological advances, and two parts are providing an insight into up-to-date applications from the fields of natural products and food analysis on the one hand and biomedical and pharmaceutical analysis on the other hand. The approaches used comprise different modes of electroseparation methods such as CZE, packed column, monolithic column and open-tubular CEC, MEKC, CIEF, CITP, different modes of ionization such as MALDI, ICP, and ESI, as well as a range of mass analyzers from simple single quadrupole MS to top of the range Q-TOF instruments, providing MS-MS and accurate mass features." [source] Fast determination of prominent carotenoids in tomato fruits by CEC using methacrylate ester-based monolithic columnsELECTROPHORESIS, Issue 22 2007Ana Maria Adalid Abstract In this study, the major carotenoids (,-carotene and lycopene) present in tomato fruits were analyzed by CEC with a methacrylate ester-based monolithic column. The effects of the porogenic solvent ratio, and the hydrophobicity of bulk monomer employed were examined on carotenoids separations. A fast separation of these analytes was achieved in less than 5.0,min in a mobile phase containing 35% THF, 30% ACN, 30% methanol, and 5% of a 5,mM Tris aqueous buffer, pH,8, with lauryl methacrylate-based monoliths. The CEC method was evaluated in terms of detection limit and reproducibility (retention time, area, and column preparation) with values below 1.6,,g/mL and 7.2%, respectively. The proposed procedure was successfully applied to the determination of both carotenoids in fruits of several tomato-related species and its usefulness to analyze large series of samples for nutritional quality screening trials in tomato breeding programs is demonstrated. To our knowledge, this is the first work that exploits the powerful and user-friendly monolithic technology for quality breeding and germplasm evaluation program purposes. [source] Hybrid silica monolithic column for capillary electrochromatography with enhanced cathodic electroosmotic flowELECTROPHORESIS, Issue 21 2006Jiwei Hu Abstract A hybrid silica monolithic stationary phase for RP CEC was prepared by in,situ co-condensation of (3-mercaptopropyl)-trimethoxysilane (MPTMS), phenyltriethoxysilane (PTES), and tetraethoxysilane (TEOS) via a sol,gel process. The thiol groups on the surface of the stationary phase were oxidized to sulfonic acids by peroxytrifluoroacetic acid. The introduced sulfonic acid moieties on the monoliths were characterized by a strong and relatively stable EOF in a broad pH range from 2.35 to 7.0 in CEC. Aromatic acids and neutral compounds can be simultaneously separated in this column under cathodic EOF. The CEC column exhibited a typical RP chromatographic mechanism for neutral compounds due to the introduced phenyl groups. [source] Capillary electrochromatography with zwitterionic stationary phase on the lysine-bonded poly(glycidyl methacrylate- co -ethylene dimethacrylate) monolithic capillary columnELECTROPHORESIS, Issue 12 2006Xiaoli Dong Abstract A polymer-based neutral monolithic capillary column was prepared by radical polymerization of glycidyl methacrylate and ethylene dimethacrylate in a 100,,m id fused-silica capillary, and the prepared monolithic column was subsequently modified based on a ring opening reaction of epoxide groups with 1,M,lysine in solution (pH,8.0) at 75°C for 10,h to produce a lysine chemically bonded stationary phases in capillary column. The ring opening reaction conditions were optimized so that the column could generate substantial EOF. Due to the zwitterionic functional groups of the lysine covalently bonded on the polymer monolithic rod, the prepared column can generate cathodic and anodic EOF by varying the pH values of running buffer during CEC separation. EOF reached the maximum of ,2.0×10,8,m2v,1s,1 and 2.6×10,8,m2v,1s,1 with pH of the running buffer of 2.25 and 10, respectively. As a consequence, neutral compounds, ionic solutes such as phenols, aromatic acids, anilines, and basic pharmaceuticals were all successfully separated on the column by CEC. Hydrophobic interaction is responsible for separation of neutral analytes. In addition, the electrostatic and hydrophobic interaction and the electrophoretic migration play a significant role in separation of the ionic or ionizable analytes. [source] A silica-based monolithic column in capillary HPLC and CEC coupled with ESI-MS or electrospray-atmospheric-pressure laser ionization-MSELECTROPHORESIS, Issue 21 2005Stefan Droste Abstract We describe the successful coupling of CEC and capillary HPLC with the recently developed atmospheric-pressure laser ionization (APLI) method. APLI is suitable for selectively and sensitively ionizing nonpolar aromatic compounds at ambient pressure for subsequent mass-selective detection. The polycyclic aromatic hydrocarbons used as analytes are first separated either by CEC on a silica-based monolithic column or by capillary HPLC. The eluent, along with a sheath flow, is volatilized by microelectrospray and then selectively ionized by excimer laser (KrF*) radiation via two-photon excitation. A QTOF-MS is used as mass-selective detector. This interface combination makes soft ionization of thermally labile nonpolar aromatic analytes possible. [source] Analyses of preservatives by capillary electrochromatography using methacrylate ester-based monolithic columnsELECTROPHORESIS, Issue 18-19 2004Hsi-Ya Huang Abstract Five common food preservatives were analyzed by capillary electrochromatography, utilizing a methacrylate ester-based monolithic capillary as separation column. In order to optimize the separation of these preservatives, the effects of the pore size of the polymeric stationary phase, the pH and composition of the mobile phase on separation were examined. For all analytes, it was found that an increase in pore size caused a reduction in retention time. However, separation performances were greatly improved in monolithic columns with smaller pore sizes. The pH of the mobile phase had little influence on separation resolution, but a dramatic effect on the amount of sample that was needed to be electrokinetically injected into the monolithic column. In addition, the retention behaviors of these analytes were strongly influenced by the level of acetonitrile in the mobile phase. An optimal separation of the five preservatives was obtained within 7.0 min with a pH 3.0 mobile phase composed of phosphate buffer and acetonitrile 35:65 v/v. Finally, preservatives in real commercial products, including cold syrup, lotion, wine, and soy sauces, were successfully determined by the methacrylate ester-based polymeric monolithic column under this optimized condition. [source] Microfluidic device for capillary electrochromatography-mass spectrometryELECTROPHORESIS, Issue 21 2003Iulia M. Lazar Abstract A novel microfabricated device that integrates a monolithic polymeric separation channel, an injector, and an interface for electrospray ionization-mass spectrometry detection (ESI-MS) was devised. Microfluidic propulsion was accomplished using electrically driven fluid flows. The methacrylate-based monolithic separation medium was prepared by photopolymerization and had a positively derivatized surface to ensure electroosmotic flow (EOF) generation for separation of analytes in a capillary electrochromatography (CEC) format. The injector operation was optimized to perform under conditions of nonuniform EOF within the microfluidic channels. The ESI interface allowed hours of stable operation at the flow rates generated by the monolithic column. The dimensions of one processing line were sufficiently small to enable the integration of 4,8 channel multiplexed structures on a single substrate. Standard protein digests were utilized to evaluate the performance of this microfluidic chip. Low- or sub-fmol amounts were injected and detected with this arrangement. [source] Surface interaction of well-defined, concentrated poly(2-hydroxyethyl methacrylate) brushes with proteinsJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 21 2007Chiaki Yoshikawa Abstract The interaction of concentrated polymer brushes with proteins was chromatographically investigated. By the use of surface-initiated atom transfer radical polymerization, a low-polydispersity poly(2-hydroxyethyl methacrylate) (PHEMA) was densely grafted onto the inner surfaces of silica monoliths with mesopores of about 50 and 80 nm in mean size. The graft density reached 0.4,0.5 chains/nm2. The 80-nm-mesopore monolithic column with the concentrated PHEMA brush was characterized through the elution of low-polydispersity pullulans with different molecular weights, clearly showing two modes of size exclusion, that is, one by the mesopores and the other by the brush phase. The latter mode gave a sharp separation with a critical molecular weight (size-exclusion limit) of about 1000. This molecular size of pullulan was comparable to the distance between the nearest-neighbor graft points. The elution behaviors of five proteins of different sizes (bovine serum thyroglobulin, bovine serum immunoglobulin G, bovine serum albumin, horse heart myoglobin, and bovine serum aprotinin) were studied with this PHEMA-grafted column. The smallest protein, aprotinin, with a pullulan-reduced molecular weight slightly larger than the critical value of 1000, was eluted much behind the corresponding pullulan, and this indicated that it barely got into the brush layer, suffering from a strong affinity interaction within the brush. On the other hand, the other four larger proteins were eluted at the same elution volumes as the equivalent pullulans, and this meant that they were perfectly excluded from the brush layer and separated only in the size-exclusion mode by the mesopores without an affinity interaction with the brush surface. This excellent inertness of the concentrated brush in the interaction with the large proteins should afford the system long-term stability against biofouling. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4795,4803, 2007 [source] Performance of wide-pore monolithic silica column in protein separationJOURNAL OF SEPARATION SCIENCE, JSS, Issue 15-16 2009Hironobu Morisaka Abstract A monolithic wide-pore silica column was newly prepared for protein separation. The wide distribution of the pore sizes of monolithic columns was evaluated by mercury porosimetry. This column, as well as the conventional monolithic column, shows high permeability in the chromatographic separation of low-molecular-sized substances. In higher-molecular-sized protein separation, the wide-pore monolithic silica column shows better performance than that of the conventional monolithic column. Under optimized conditions, five different proteins , ribonuclease A, albumin, aldolase, catalase, and ferritin , were baseline-separated within 3 min, which is faster than that using the particle-packed columns. In addition, the monolithic wide-pore silica column could also be prepared in fused silica capillary (600 mm long, 0.2 mm i.d.) for highly efficient protein separation. The peak capacity of the wide-pore monolithic silica capillary column is estimated to be approximately 300 in the case of protein separation, which is a characteristic performance. [source] Silica-based monolithic column with evaporative light scattering detector for HPLC analysis of bacosides and apigenin in Bacopa monnieriJOURNAL OF SEPARATION SCIENCE, JSS, Issue 15-16 2009Pamita Bhandari Abstract A high performance liquid chromatographic method using a silica-based monolithic column coupled with evaporative light scattering detector (HPLC,ELSD) was developed and validated for simultaneous quantification of bacosides (bacoside A, bacopaside I, bacoside A3, bacopaside II, bacopaside X, bacopasaponin C) and apigenin in Bacopa monnieri. The chromatographic resolution was achieved on a Chromolith RP-18 (100×4.6 mm) column with acetonitrile/water (30:70) as mobile phase in isocratic elution at a flow rate of 0.7 mL/min. The drift tube temperature of the ELSD was set to 95°C, and the nitrogen flow rate was 2.0 SLM (standard liter per minute). The calibration curves revealed a good linear relationship (r2 >0.9988) within the test ranges. The detection limits (S/N = 3) and the quantification limits (S/N = 10) for the compounds were in the range of 0.54,6.06 and 1.61,18.78 ,g/mL, respectively. Satisfactory average recovery was observed in the range of 95.8,99.0%. The method showed good reproducibility for the quantification of these compounds in B. monnieri with intra- and inter-day precision of less than 0.69 and 0.67%, respectively. The validated method was successfully applied to quantify analytes in nine accessions of B. monnieri and thus provides a new basis for overall quality assessment of B. monnieri. [source] Determination of fluoroquinolone antibiotics in surface waters from Mondego River by high performance liquid chromatography using a monolithic columnJOURNAL OF SEPARATION SCIENCE, JSS, Issue 17 2007Angelina Pena Abstract A novel LC,fluorescence detection method based on the use of a monolithic column for the determination of norfloxacin, ciprofloxacin, and enrofloxacin antibiotic residues in environmental waters was developed. Fluoroquinolones (FQs) were isocratically eluted using a mobile phase consisting of 0.025 M phosphoric acid solution at pH 3.0 with tetrabutylammonium and methanol (960:40, v/v) through a Chromolith Performance RP-18e column (100×4.6 mm) at a flow rate of 2.5 mL/min and detected at excitation and emission wavelengths of 278 and 450 nm, respectively. After acidification and addition of EDTA, water samples were extracted using an Oasis HLB cartridge. Linearity was evaluated in the range of 0.05 to 1 ,g/mL and correlation coefficients of 0.9945 for norfloxacin, 0.9974 for ciprofloxacin, and 0.9982 for enrofloxacin were found. The limit of quantification was 25 ng/L for the three FQs. The recovery of FQs spiked into river water samples at 25, 50, and 100 ng/L fortification levels ranged from 76.5 to 91.0% for norfloxacin, 78.5 to 97.2% for ciprofloxacin, and 79.4 to 93.6% for enrofloxacin. This method was successfully applied to the analysis of water samples from the Mondego River, and ciprofloxacin and enrofloxacin residues were detected in eight water samples. [source] Separation and determination of five major opium alkaloids with mixed mode of hydrophilic/cation-exchange monolith by pressurized capillary electrochromatographyJOURNAL OF SEPARATION SCIENCE, JSS, Issue 17 2007Xucong Lin Abstract A method for the separation and determination of five major opium alkaloids (narcotine, papaverine, thebaine, codeine, and morphine) in pericarpium papaveris by pressurized CEC (pCEC) with monolithic column has been developed. Under the optimum condition, linear calibration ranges of narcotine, papaverine, thebaine, codeine, and morphine were obtained as 2,85, 2,85, 5,75, 10,65, and 10,65 ,g/mL, respectively. LODs of these analytes were 1.5,6.0 ,g/mL. The RSD (n = 7) of the migration time and peak area were 1.94,5.24 and 4.05,8.21%, respectively. The proposed method was successfully applied to the analysis of pericarpium papaveris samples. Average recoveries of 79.0,95.9% at different fortified levels of alkaloids were achieved with RSD less than 4.6%. Meanwhile, the mechanism of the separation of the alkaloids on the monolithic column was also discussed. The result showed that the separation of alkaloids was mainly based on the mixed mode of hydrophilic interaction (HI) and cation exchange. [source] Alkylated poly(styrene-divinylbenzene) monolithic columns for ,-HPLC and CEC separation of phenolic acidsJOURNAL OF SEPARATION SCIENCE, JSS, Issue 17 2007Zdenka Ku, erová Abstract Macroporous poly(styrene-divinylbenzene) monolithic columns were prepared in fused silica capillaries of 100 ,m id by in-situ copolymerization of styrene with divinylbenzene in the presence of propan-1-ol and formamide as the porogen system. The monoliths were subsequently alkylated with linear alkyl C-18 groups via Friedel-Crafts reaction to improve the retention and chromatographic resolution of strongly polar phenolic acids. A new thermally initiated grafting procedure was developed in order to shorten the time of the alkylation process. The grafting procedure was optimized with respect to the reaction temperature, time, the grafting reactant concentration, and the solvent used. The type of solvent and the grafting temperature are the most significant factors affecting the hydrodynamic properties, porosity, and efficiency of the columns. While the equivalent particle diameter of the grafted column increased, the capillary-like flow-through pore diameter decreased in comparison to non-alkylated monoliths. The hydrodynamic permeability of the monolith decreased, but the monolithic column still permitted fast ,-HPLC separations. [source] Preparation of a monolithic column for weak cation exchange chromatography and its application in the separation of biopolymersJOURNAL OF SEPARATION SCIENCE, JSS, Issue 1 2006Yinmao Wei Abstract A procedure for the preparation of a monolithic column for weak cation exchange chromatography was presented. The structure of the monolithic column was evaluated by mercury intrusion. The hydrodynamic and chromatographic properties of the monolithic column , such as back pressures at different flow rates, effects of pH on protein retention, dynamic loading capacity, recovery, and stability , were determined under conditions typical for ion-exchange chromatography. The prepared monolithic column might be used in a relatively broad pH range from 4.0 to 12.0 and exhibited an excellent separation to five proteins at the flow rates of both 1.0 and 8.0 mL/min, respectively. In addition, the prepared column was first used in the purification and simultaneous renaturation of recombinant human interferon gamma (rhIFN-,) in the extract solution with 7.0 mol/L guanidine hydrochloride. The purity and specific bioactivity of the purified rhIFN-, in only one chromatographic step were obtained to be 93% and 7.8×107 IU/mg, respectively. [source] A computational study of the porosity effects in silica monolithic columnsJOURNAL OF SEPARATION SCIENCE, JSS, Issue 10-11 2004Piotr Gzil Abstract We report on a theoretical study of the influence of the through-pore porosity on the main chromatographic performance parameters (reduced theoretical plate height, flow resistance, and separation impedance) of silica monoliths. To investigate this problem devoid of any structural uncertainties, computer-generated structural mimics of the pore geometry of silica monolithic columns have been studied. The band broadening in these synthetic monoliths was determined using a commercial Computational Fluid Dynamics (CFD) software package. Three widely differing external porosities (, = 0.38, , = 0.60, and , = 0.86) are considered and are compared on the basis of an identical intra-skeleton diffusivity (D s = 5×10,10m2/s), internal porosity (,int = 0.5), and for the same phase retention factor (k ´ = 1.25). Since the data are obtained for perfectly ordered structures, the calculated plate heights and separation impedances constitute the ultimate performance ever to be expected from a monolithic column. It is found that, if silica monoliths could be made perfectly homogeneous, domain size-based reduced plate heights as small as h min , 0.8 (roughly independent of the porosity) and separation impedances as small as Emin , 130 (, = 0.60) and Emin , 40 (, = 0.86) should be achievable with pure water as the working fluid. The data also show that, although the domain size is a much better reduction basis than the skeleton size, the former is still not capable of bringing the van Deemter curves of different porosity columns into perfect agreement in the C term dominated velocity range. It is found that, in this range, large porosity monoliths can be expected to yield smaller domain size-based reduced plate heights than small porosity monoliths. [source] Reduced-bore monolithic silica column modified with C8 -TEOS for reversed-phase electrochromatographyJOURNAL OF SEPARATION SCIENCE, JSS, Issue 9 2004Qishu Qu Abstract Monolithic silica columns of 2.7 mm ID were prepared and derivatized with C8 -TEOS and TEOS by on-column sol-gel reaction. These C8 large diameter monolithic silica columns gave 21 000 theoretical plates for aromatic hydrocarbons in 60% acetonitrile and 40% Tris-HCl buffer. The surface areas as well as the separation reproducibility were improved on coating by the sol-gel approach. Joule heating was greatly reduced by using monolithic columns to which fine quartz sand had been added during column preparation. Since this is a preliminary investigation on a monolithic column with such a large inner diameter, the separation efficiency was not so high as that presently achieved in normal capillary electrochromatography (CEC). However, use of the columns improved sample loadability and concentration detectability of electrochromatography, and semi-preparative separations could be performed. [source] A high-throughput monolithic HPLC method for rapid Vitamin C phenotyping of berry fruitPHYTOCHEMICAL ANALYSIS, Issue 5 2006Paul G. Walker Abstract A rapid method for the quantification of ,ascorbic acid (1) in berry fruit by HPLC with photodiode array detection is presented. ,Ascorbic acid was resolved on a C18 monolithic column with aqueous buffer, after which the column was washed with acetonitrile to remove lipophilic compounds prior to re-equilibration for analysis of the next sample. Using the monolithic column format with high mobile phase flow rates, the entire separation, wash and re-equilibration were achieved in 3 min. With the exception of gooseberry (Ribes uva-crispa), for which an interfering compound co-eluted, concentrations of 1 could be determined in a wide range of berry fruits after extraction in metaphosphoric acid without further sample preparation. Using this extraction method, recoveries of 1 in excess of 85% were achieved. Fruit or juice extracts were stable in 5% metaphosphoric acid for at least 4 h and stability could be extended to longer than 150 h by the addition of the reducing agent tris(2-carboxethyl)phosphine hydrochloride. Following validation, the method was utilised for the phenotyping of fruit in a Scottish Crop Research Institute (SCRI) Ribes nigrum L. breeding population of 300 individuals. An improved extraction method allowed extraction, quantification of 1 and data analysis to be undertaken in less than one working week. Copyright © 2006 John Wiley & Sons, Ltd. [source] Semi-online nanoflow liquid chromatography/matrix-assisted laser desorption ionization mass spectrometry of synthetic polymers using an octadecylsilyl-modified monolithic silica capillary columnRAPID COMMUNICATIONS IN MASS SPECTROMETRY, Issue 13 2010Takehiro Watanabe We have designed a semi-online liquid chromatography/matrix-assisted laser desorption/ionization mass spectrometry (LC/MALDI-MS) system to introduce eluent from a octadecylsilyl (ODS) group modified monolithic silica capillary chromatographic column directly onto a sample plate for MALDI-MS analysis. Our novel semi-online system is useful for rapidly and sensitively examining the performance of a monolithic capillary column. An additional advantage is the small elution volume of a monolithic capillary column, which allows delicate eluents, such as 1,1,1,3,3,3,-hexafluoroisopropyl alcohol (HFIP), to be used to achieve cost-effective analysis. Using the semi-online LC/MALDI-MS system, chromatographic separation of polymers by the monolithic column with different eluents was studied. Separation of poly(methyl methacrylate) and Nylon 6/6 showed that the column functioned via size-exclusion separation when tetrahydrofuran or HFIP eluent was used. On the other hand, the separation behavior of Nylon 11 indicated a reversed-phase mode owing to the interaction of the polymer with the modified ODS group in the column. Using tetrahydrofuran/methanol (1:1, v/v) as the eluent, the LC/MALDI-MS spectra of poly(lactic acid), which contains both linear and cyclic polymer structures, showed that the column could separate the hydrophobic cyclic polymer and elute it out relatively slowly. The monolithic column functions basically via size-exclusion separation; the reversed-phase separation by interaction with the ODS functions may have less influence on column separation. The semi-online monolithic capillary LC/MALDI-MS method we have developed should provide a means of effectively analyzing synthetic polymers. Copyright © 2010 John Wiley & Sons, Ltd. [source] | |||||||||||||