Home About us Contact
|
Home About us Contact | ||
|
|
||
Mobility Measurements (mobility + measurement)
Selected AbstractsUnderivatized cyclic olefin copolymer as substrate material and stationary phase for capillary and microchip electrochromatographyELECTROPHORESIS, Issue 15 2008Omar Gustafsson Abstract We report, for the first time, the use of underivatized cyclic olefin copolymer (COC, more specifically: Topas) as the substrate material and the stationary phase for capillary and microchip electrochromatography (CEC), and demonstrate chromatographic separations without the need of coating procedures. Electroosmotic mobility measurements in a 25,,m id Topas capillary showed a significant cathodic EOF that is pH-dependent. The magnitude of the electroosmotic mobility is comparable to that found in glass substrates and other polymeric materials. Open-tubular CEC was employed to baseline-separate three neutral compounds in an underivatized Topas capillary with plate heights ranging from 5.3 to 12.7,,m. The analytes were detected using UV absorbance at 254,nm, thus taking advantage of the optical transparency of Topas at short wavelengths. The fabrication of a Topas-based electrochromatography microchip by nanoimprint lithography is also presented. The microchip has an array of pillars in the separation column to increase the surface area. The smallest features that were successfully imprinted were around 2,,m wide and 5,,m high. No plasma treatment was used during the bonding, thus keeping the surface properties of the native material. An RP microchip electrochromatography separation of three fluorescently labeled amines is demonstrated on the underivatized microchip with plate heights ranging from 3.4 to 22,,m. [source] The Effect of Polymer Optoelectronic Properties on the Performance of Multilayer Hybrid Polymer/TiO2 Solar CellsADVANCED FUNCTIONAL MATERIALS, Issue 4 2005P. Ravirajan Abstract We report a study of the effects of polymer optoelectronic properties on the performance of photovoltaic devices consisting of nanocrystalline TiO2 and a conjugated polymer. Three different poly(2-methoxy-5-(2,-ethylhexoxy)-1,4-phenylenevinylene) (MEH-PPV)-based polymers and a fluorene,bithiophene copolymer are compared. We use photoluminescence quenching, time-of-flight mobility measurements, and optical spectroscopy to characterize the exciton-transport, charge-transport, and light-harvesting properties, respectively, of the polymers, and correlate these material properties with photovoltaic-device performance. We find that photocurrent is primarily limited by the photogeneration rate and by the quality of the interfaces, rather than by hole transport in the polymer. We have also studied the photovoltaic performance of these TiO2/polymer devices as a function of the fabrication route and device design. Including a dip-coating step before spin-coating the polymer leads to excellent polymer penetration into highly structured TiO2 networks, as was confirmed through transient optical measurements of the photoinduced charge-transfer yield and recombination kinetics. Device performance is further improved for all material combinations studied, by introducing a layer of poly(ethylene dioxythiophene) (PEDOT) doped with poly(styrene sulfonic acid) (PSS) under the top contact. Optimized devices incorporating the additional dip-coated and PEDOT:PSS layers produced a short-circuit current density of about 1,mA,cm,2, a fill factor of 0.50, and an open-circuit voltage of 0.86,V under simulated AM,1.5 illumination (100,mW,cm,2, 1,sun). The corresponding power conversion efficiency under 1,sun was ,,0.4,%. [source] Silicon Nanowires: A Review on Aspects of their Growth and their Electrical PropertiesADVANCED MATERIALS, Issue 25-26 2009Volker Schmidt Abstract This paper summarizes some of the essential aspects of silicon-nanowire growth and of their electrical properties. In the first part, a brief description of the different growth techniques is given, though the general focus of this work is on chemical vapor deposition of silicon nanowires. The advantages and disadvantages of the different catalyst materials for silicon-wire growth are discussed at length. Thereafter, in the second part, three thermodynamic aspects of silicon-wire growth via the vapor,liquid,solid mechanism are presented and discussed. These are the expansion of the base of epitaxially grown Si wires, a stability criterion regarding the surface tension of the catalyst droplet, and the consequences of the Gibbs,Thomson effect for the silicon wire growth velocity. The third part is dedicated to the electrical properties of silicon nanowires. First, different silicon nanowire doping techniques are discussed. Attention is then focused on the diameter dependence of dopant ionization and the influence of interface trap states on the charge carrier density in silicon nanowires. It is concluded by a section on charge carrier mobility and mobility measurements. [source] Drying-induced variations in physico-chemical properties of amorphous pharmaceuticals and their impact on stability (I): Stability of a monoclonal antibody,JOURNAL OF PHARMACEUTICAL SCIENCES, Issue 8 2007Ahmad M. Abdul-Fattah Abstract The present study was conducted to investigate the impact of drying method and formulation on the storage stability of IgG1. Formulations of IgG1 with varying levels of sucrose with and without surfactant were dried by different methods, namely freeze drying, spray drying, and foam drying. Dried powders were characterized by thermal analysis, scanning electron microscopy, specific surface area (SSA) analysis, electron spectroscopy for chemical analysis (ESCA), solid state FTIR, and molecular mobility measurements by both isothermal calorimetry and incoherent elastic neutron scattering. Dried formulations were subjected to storage stability studies at 40°C and 50°C (aggregate levels were measured by size exclusion chromatography initially and at different time points). Both drying method and formulation had a significant impact on the properties of IgG1 powders, including storage stability. Among the drying methods, SSA was highest and perturbations in secondary structure were lowest with the spray-dried preparations. Sucrose-rich foams had the lowest SSA and the lowest protein surface accumulation. Also, sucrose-rich foams had the lowest molecular mobility (both fast dynamics and global motions). Stability studies showed a log-linear dependence of physical stability on composition. Preparations manufactured by "Foam Drying" were the most stable, regardless of the stabilizer level. In protein-rich formulations, freeze-dried powders showed the poorest storage stability and the stability differences were correlated to differences in secondary structure. In stabilizer-rich formulations, stability differences were best correlated to differences in molecular mobility (fast dynamics) and total protein surface accumulation. © 2007 Wiley-Liss, Inc. and the American Pharmacists Association J Pharm Sci 96:1983,2008, 2007 [source] | ||||||||||