Home About us Contact
|
Home About us Contact | ||
|
|
||
Miniemulsion Droplets (miniemulsion + droplet)
Selected AbstractsSynthesis of oily core-hybrid shell nanocapsules through interfacial free radical copolymerization in miniemulsion: Droplet formation and nucleationJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 3 2010Z. H. Cao Abstract Nanocapsules with an oily core and an organic/inorganic hybrid shell were elaborated by miniemulsion (co)polymerization of styrene, divinylbenzene, ,-methacryloyloxy propyl trimethoxysilane, and N -isopropyl acrylamide. The hybrid copolymer shell membrane was formed by polymerization-induced phase separation at the interface of the oily nanodroplets with water. It was shown that the size, size distribution, and colloidal stability of the miniemulsion droplets were extremely dependent on the nature of the oil phase, the monomer content and the surfactant concentration. The less water-soluble the hydrocarbon template and the higher the monomer content, the better the droplet stability. The successful formation of nanocapsules with the targeted core-shell morphology (i.e., a liquid core surrounded by a solid shell) was evidenced by cryogenic transmission electron microscopy. Both nanocapsules and nanoparticles were produced by polymerization of the miniemulsion droplets. The proportion of nanoparticles increased with increasing monomer concentration in the oil phase. These undesirable nanoparticles were presumably formed by homogeneous nucleation as we showed that micellar nucleation could be neglected under our experimental conditions even for high surfactant concentrations. The introduction of ,-methacryloyloxy propyl trimethoxysilane was considered to be the main reason for homogeneous nucleation. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 593,603, 2010 [source] Morphology of Polymer/Clay Latex Particles Synthesized by Miniemulsion Polymerization: Modeling and Experimental ResultsMACROMOLECULAR REACTION ENGINEERING, Issue 6-7 2010Matej Mi Abstract BA/MMA (90:10,wt.-%) were copolymerized in the presence of two different organomodified clays (C30B and CMA16) and 1.6,2.6,wbm.-% surfactants. The effect of the compatibility of the organoclay in the monomer mixture on the morphology of hybrid polymer/clay particles was determined using TEM. The resulting morphologies were compared with the prediction of a Monte-Carlo simulation that determined the equilibrium morphology of monomer/clay hybrid miniemulsion droplets. The model predicted encapsulated morphologies only when the organoclay presented low clay/monomer and high clay/water interfacial tensions. C30B and CMA16 did not fulfill these conditions and provided a preferential surface location of the platelets on the polymer/water interphase as predicted by the model. [source] Polymerisable Miniemulsions Using Rotor-Stator HomogenisersMACROMOLECULAR REACTION ENGINEERING, Issue 4 2008Ula El-Jaby Abstract The use of a rotor-stator mixer as a homogenisation device to make miniemulsion droplets with industrially pertinent solid contents was investigated. Methyl methacrylate/butyl acrylate (50:50 w/w ratio) miniemulsions with droplet diameters from 2 µm to 300 nm and polydispersity indices from 1.2 to 3.6 were used. Miniemulsions with three different mean droplet diameters (300, 400, 600 nm) were polymerised and the evolution of particle size was observed. When 300 nm droplets were polymerised they yielded particles of similar diameter to the original droplets, whereas particle coalescence of the growing particles with a loss of control over the particle size distribution was observed for the 400 and 600 nm droplets. The influence of costabiliser, agitation speed, solid content, colloidal protectors and surface coverage on the evolution of the droplet size and size distribution as well as on the evolution of the average particle size and its distribution were examined. It was observed that changing the above parameters had no impact on the evolution of the particle size, suggesting we have a very robust miniemulsion system. [source] (Mini)emulsion Polymerization: Effect of the Segregation Degree on Polymer ArchitectureMACROMOLECULAR REACTION ENGINEERING, Issue 6 2007Iker González Abstract A continuous loop reactor was used for the production of 2-ethylhexyl acrylate (2-EHA), methyl methacrylate (MMA) and acrylic acid (AA) pressure sensitive adhesive by both emulsion and miniemulsion polymerization. Similar high monomer conversions were achieved in both processes, but striking differences in polymer architecture were found. A mathematical model was used to analyze these differences concluding that because the costabilizer suppressed monomer diffusion from miniemulsion droplets, the average polymer concentration in the polymerization loci was lower in the miniemulsion process. This resulted in less chain transfer to polymer, and hence in lower sol molecular weight and gel content. [source] | ||||||||||