Home About us Contact
|
Home About us Contact | ||
|
|
||
Metallic Surface (metallic + surface)
Selected AbstractsElectrodeposition of Titania Thin Films on Metallic Surface for High- k Dielectric ApplicationsJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 3 2010Biplab K. Roy Current microelectronics devices based on flexible as well as rigid substrates demand high dielectric constant (k) films to be grown on conductive substrate from a low-cost, low-temperature deposition technique. In this study, we produced high- k titania (TiO2) films through an affordable electrodeposition protocol from the electrochemical bath maintained at about 0°C. The deposition occurs through a rapid hydrolysis mechanism of titanium containing ions in the precursor solution aided by electrochemically generated hydroxyl ions formed near the cathode surface (copper (Cu) substrate). Upon attaining a sufficient supersaturation level, such hydrolyzed species precipitate to form a titania thin film on the cathode surface. While depositing from a highly acidic precursor solution, Cu substrate was protected by a cathodic potential (,3 to ,5 V against the counter electrode). The resultant titania films show nanoparticulate structures evolved from nucleation and growth events of the in situ precipitated particles. Much higher deposition rate (about 1 ,m/min) was observed compared with that of typical chemical bath deposition. The resultant films with a thickness of 1500 nm grown on Cu exhibit very high dielectric properties (e.g., k,30, capacitance density >110 nF/in.2 at 100 kHz) and moderate breakdown voltage (VB) (,17.5 V). These properties indicate the potential of electrodeposited titania films to be used as a small-area thin-film capacitor for miniaturized electronic devices. [source] Atomic-Level Studies of Molecular Self-Assembly on Metallic SurfacesADVANCED MATERIALS, Issue 10-11 2009Giulia Tomba Abstract Shrinking devices to the nanoscale, while still maintaining accurate control on their structure and functionality is one of the major technological challenges of our era. The use of purposely directed self-assembly processes provides a smart alternative to the troublesome manipulation and positioning of nanometer-sized objects piece by piece. Here, we report on a series of recent works where the in-depth study of appropriately chosen model systems addresses the two key-points in self-assembly: building blocks selection and control of bonding. We focus in particular on hydrogen bonding because of the stability, precision and yet flexibility of nanostructures based on this interaction. Complementing experimental information with advanced atomistic modeling techniques based on quantum formalisms is a key feature of most investigations. We thus highlight the role of theoretical modeling while we follow the progression in the use of more and more complex molecular building blocks, or "tectons". In particular, we will see that the use of three-dimensional, flexible tectons promises to be a powerful way to achieve highly sophisticated functional nanostructures. However, the increasing complexity of the assembly units used makes it generally more difficult to control the supramolecular organization and predict the assembling mechanisms. This creates a case for developing novel analysis methods and ever more advanced modeling techniques. [source] Synthesis of New Tripodal Tri-Functionalized Hydrotris(indazol-1-yl)borate Ligands and X-ray Structures of Their Cyclopentadieneruthenium ComplexesEUROPEAN JOURNAL OF INORGANIC CHEMISTRY, Issue 5 2006Alexandre Carella Abstract Two new tripodal ligands designed to anchor complexes onto surfaces have been synthesized. They integrate ester or thioether functions at the 6-position of the indazoles. Potassium hydrotris[6-(ethoxycarbonyl)indazolyl]borate and potassium hydrotris{6-[(ethylsulfanyl)methyl]indazolyl}borate exhibit three pendant groups oriented to anchor complexes onto an oxide and a metallic surface, respectively. Their complexation with [RuCp(CH3CN)3]PF6 yielded two piano-stool-shaped complexes that were characterized by X-ray diffraction. Comparison with the synthesized unfunctionalized analog showed that the three 6-substituted functions do not interfere with the coordination site and are particularly well oriented for surface deposition.(© Wiley-VCH Verlag GmbH & Co. KGaA, 69451 Weinheim, Germany, 2006) [source] Ultrasonic Metal Welding of Aluminium Sheets to Carbon Fibre Reinforced Thermoplastic Composites,ADVANCED ENGINEERING MATERIALS, Issue 1-2 2009Frank Balle The ultrasonic welding technology is an innovative method to produce hybrid joints for multi-material components. The investigations described in this paper were carried out using the ultrasonic metal welding technique for joining carbon fibre reinforced thermoplastic composites (CFRP) with sheet metals like aluminium alloys or aluminium-plated steels. The achievable mechanical properties as a function of the process parameters are presented. Additionally, microscopic investigations of the bonding zone are discussed. One important advantage of ultrasonic metal welding is the possibility to realise a direct contact between the load bearing fibres of the reinforced composite and the metallic surface without destroying the carbon fibres. [source] Quantitative evaluation of the prosthetic head damage induced by microscopic third-body particles in total hip replacementJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 4 2001Manuela Teresa Raimondi Abstract The increase of the femoral head roughness in artificial hip joints is strongly influenced by the presence of abrasive particulate entrapped between the articulating surfaces. The aim of the present study is to evaluate the dependence of such damage on the geometry of the particles entrapped in the joint, with reference to the UHMWPE/chrome-cobalt coupling. Five chrome-cobalt femoral heads and their coupled UHMWPE acetabular cups, retrieved at revision surgery after a short period of in situ functioning, have been investigated for the occurrence of third-body damage. This was found on all the prosthetic heads, where the peak-to-valley height of the scratches, as derived from profilometry evaluations, ranged from 0.3,1.3 ,m. The observed damage has been divided into four classes, related to the particle motion while being embedded into the polymer. Two kinds of particle morphology have been studied, spherical and prismatic, with size ranging from 5,50 ,m. In order to provide an estimation of the damage induced by such particles, a finite element model of the third-body interaction was set up. The peak-to-valley height of the impression due to the particle indentation on the chrome-cobalt surface is assumed as an index of the induced damage. The calculated values range from 0.1,0.5 ,m for spherical particles of size ranging from 10,40 ,m. In the case of prismatic particles, the peak-to-valley height can reach 1.3 ,m and depends both on the size and width of the particle's free corner, indenting the chrome-cobalt. As an example, a sharp-edged particle of size 30 ,m can induce on the chrome-cobalt an impression with peak-to-valley height of 0.75 ,m, when embedded into the polyethylene with a free edge of 5 ,m facing the metallic surface. Negligible damage is induced, if a free edge of 7.5 ,m is indenting the counterface. Our findings offer new support to the hypothesis that microscopic third-body particles are capable of causing increased roughening of the femoral head and provide a quantitative evaluation of the phenomenon. © 2001 John Wiley & Sons, Inc. J Biomed Mater Res (Appl Biomater) 58: 436,448, 2001 [source] Biodegradable poly(D,L -lactide) coating of implants for continuous release of growth factorsJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 4 2001G. Schmidmaier Abstract Local application of growth factors like insulin like growth factor-I (IGF-I) and transforming growth factor-beta 1 (TGF-,1) from a biodegradable thin layer of poly(D,L -lactide) (PDLLA) coated implants could stimulate fracture healing. A new "cold coating technique" for metallic implants was established to produce a biodegradable coating with a high mechanical stability that provides a continuous release of incorporated growth factors. The properties of this bioactive coating were investigated in vitro and in vivo. Scanning electron microscope analysis revealed a coating thickness of in average 14.8 ,m on titanium and 10.7 ,m on steel wires. Intramedullary implantation and extraction experiments depicted a loss of PDLLA coating from titanium and steel implants of less than 5%. After explantation of the implants, the coating displayed a complete and regular layer without any defects of PDLLA uncovering the metallic surface. Smear tests demonstrate that the coating can be performed under sterile conditions. The PDLLA depicted a reduction of about 8% within 6 weeks in vitro and in vivo. The growth factors were incorporated in a stable form and demonstrated a loss of stability of less than 3% within 42 days and less than 5% within one year. In an elution experiment, 54% IGF-I and 48% TGF-,1 were released within the first 48 h. After 42 days, 76% of IGF-I and 71% of TGF-,1 were detected in the elution fluid by ELISA. Comparable results were obtained in the in vivo experiments after 42 days. © 2001 John Wiley & Sons, Inc. J Biomed Mater Res (Appl Biomater) 58: 449,455, 2001 [source] Electrosensory avoidance of metal obstacles by the paddlefishJOURNAL OF FISH BIOLOGY, Issue 2 2000C. Gurgens Paddlefish Polyodon spathula detected and avoided obstacles with an exposed metallic surface but not plastic objects. An aluminium obstacle was avoided from significantly greater minimum approach distances than were any of the other obstacles. No significant difference was detected between the plastic and plastic-covered aluminium obstacles, while control values were significantly less than for all obstacle types. Avoidance distances measured at different water conductivities were not significantly different. Fish collided frequently with the plastic and plastic-covered aluminium obstacles, and with the control site, suggesting that these obstacles were not detected by the electrosensory apparatus. The aluminium obstacle was avoided successfully in all test runs. The unambiguous avoidance behaviour elicited by the aluminium obstacle suggests that large metallic structures, such as locks and dams, have the potential to interfere with paddlefish migrations. ©2000 The Fisheries Society of the British Isles [source] Surface-enhanced Raman scattering and density functional theory studies of bis(4-aminophenyl)sulfone,JOURNAL OF RAMAN SPECTROSCOPY, Issue 2 2010Guillermo Diaz-Fleming Abstract Raman and surface-enhanced Raman scattering (SERS) spectra of dapsone by using colloidal silver nanoparticles have been recorded. Density functional theory was used for the optimization of ground state geometries and simulation of the vibrational spectrum of this molecule. The SERS spectrum with a large silver cluster as a model metallic surface was simulated for the first time. Taking into account the experimental and calculated Raman as well as the SERS normal modes and the corresponding assignments, along with the modeling of the free dapsone and the one in the presence of the colloidal silver nanoparticles, the importance of the sulfone group on the SERS effect in dapsone was inferred. Copyright © 2009 John Wiley & Sons, Ltd. [source] FMR study of amorphous Co68Mn7Si10B15 glass-coated microwiresPHYSICA STATUS SOLIDI (A) APPLICATIONS AND MATERIALS SCIENCE, Issue 1 2003R. Zuberek Abstract The magnetic properties of Co68Mn7Si10B15 glass coated amorphous microwires of about 16.5 ,m in diameter have been investigated from liquid helium up to room temperature by ferromagnetic resonance at 9.243 GHz. Based on the results of measurements both the magnetic anisotropy constants, the first arising from the stress at the interface between the metallic surface and the coating and the second one of the inner core have been obtained for the room temperature. The effective anisotropy field was determined in the range from the liquid helium to the room temperature. [source] Semi-classical calculation of resonant states of a charged particle interacting with a metallic surfacePHYSICA STATUS SOLIDI (B) BASIC SOLID STATE PHYSICS, Issue 10 2005John Jairo Zuluaga Abstract We assess the applicability of the semi-classical approach of Herman,Kluk with filter diagonalization to determine resonant states of either the electron-surface system or the ion-surface system. An effective potential model of the interaction of an electron with a ruthenium metallic surface is used. The evolution of the wave-function and the resonant states of this system are calculated. Analogous results for the interaction of the system formed by the H, and the ruthenium surface are presented. For the calculation of the resonances, the semi-classical wave-function is found, and the autocorrelation function between the initial and final wave-functions is calculated, from which the position and width of the resonances are extracted by using the harmonic inversion by filter diagonalization. The results are compared with results available in the literature for similar models obtained by quantum calculations using fast Fourier Transform. The positions of the lower-lying resonances found with the semi-classical and quantum approaches match closely, while the values of the widths of the resonances show larger discrepancies. (© 2005 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] Colours and Metallic Sheen in Beetle Shells , A Biomimetic Search for Material Structuring Principles Causing Light Interference,ADVANCED ENGINEERING MATERIALS, Issue 4 2008T. Lenau Abstract Visual aesthetic has always played a vital role for the success of many products. This includes colours and glossiness and metal appearance which is often achieved using surface coatings. Present coating techniques do, however, have limitations. It is difficult to reach very bright and brilliant colours, colours tend to fade over time and many of the materials and coating technologies pollute and have other environmental problems. Beetles in nature have many of the desired properties: They have appealing brilliant colours and some even with metallic appearance. It is noticeable that the colours are long lasting as some of the beetles we have studied at the zoological museum are more than 200 years old and have colours and brightness as if they were still alive. Furthermore, the beetles in nature are part of sustainable ecosystems, which means that they are made from renewable materials that are broken down and recycled when the beetle dies. Beetles also possess another and very attractive property: Their metallic look originates from structures in organic materials which is both electrically and thermal insulating. The industrial perspective is to be able to manufacture products with attractive metallic surfaces that do not feel so cold to touch as their metallic counterparts and that do not represent an electrical shock hazard. [source] Electronic Decoupling of Aromatic Molecules from a Metal by an Atomically Thin Organic Spacer,ADVANCED MATERIALS, Issue 23 2008Roman Forker Electronic coupling effects of organic adsorbates to metallic surfaces are examined optically. Covering a Au(111) substrate with an ultrathin (,0.3 nm) nanographene-like layer of flat lying molecules leads to decoupling of further molecular layers to a large extent. Our work suggests that not only inorganic salts or oxides can be used as insulating spacers but also particular organic monolayers. [source] Transfer of metallic debris from the metal surface of an acetabular cup to artificial femoral heads by scraping: Comparison between alumina and cobalt,chrome headsJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 1 2008Chong Bum Chang Abstract We aimed to investigate the transfer of metal to both ceramic (alumina) and metal (cobalt,chrome) heads that were scraped by a titanium alloy surface under different load conditions. The ceramic and metal heads for total hip arthroplasties were scraped by an acetabular metal shell under various loads using a creep tester. Microstructural changes in the scraped area were visualized with a scanning electron microscope, and chemical element changes were assessed using an energy dispersive X-ray spectrometry. Changes in the roughness of the scraped surface were evaluated by a three-dimensional surface profiling system. Metal transfer to the ceramic and metal heads began to be detectable at a 10 kg load, which could be exerted by one-handed force. The surface roughness values significantly increased with increasing test loads in both heads. When the contact force increased, scratching of the head surface occurred in addition to the transfer of metal. The results documented that metallic debris was transferred from the titanium alloy acetabular shell to both ceramic and metal heads by minor scraping. This study suggests that the greatest possible effort should be made to protect femoral heads, regardless of material, from contact with metallic surfaces during total hip arthroplasty. © 2007 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2008 [source] A structure/function study of polyaminoamide dendrimers as silica scale growth inhibitorsJOURNAL OF CHEMICAL TECHNOLOGY & BIOTECHNOLOGY, Issue 6 2005Konstantinos D Demadis Abstract Dendrimers have attracted immense attention during the last decade due to their interesting properties both from a basic and an applied research viewpoint. Encapsulation of metal nanoparticles for catalysis, drug delivery and light harvesting are only some applications of dendrimers that are breaking new ground. A novel application of dendrimer technology is described in the present paper that relates to industrial water treatment. Industrial water systems often suffer from undesirable inorganic deposits. These can form either in the bulk or on metallic surfaces, such as heat exchangers or pipelines. Silica (SiO2) scale formation and deposition is a major problem in high-silica-containing cooling waters. Scale prevention rather than removal is highly desired. In this paper, benchtop screening tests on various silica inhibition chemistries are reported, with emphasis on materials with a dendrimeric structure. Specifically, the inhibition properties of commercially available STARBURST® polyaminoamide (PAMAM) dendrimers generations 0.5, 1, 1.5, 2, and 2.5 are investigated in detail together with other commonly-used scale inhibitors. Experimental results show that inhibition efficiency largely depends on structural features of PAMAM dendrimers such as generation number and nature of the end groups. PAMAM dendrimers are effective inhibitors of silica scale growth at 40 ppm dosage levels. PAMAM dendrimers also act as silica nucleators, forming SiO2,PAMAM composites. This occurs because the SiO2 formed by incomplete inhibition interacts with cationic PAMAM-1 and -2. The general scope of silica formation and inhibition in industrial waters is also discussed. Copyright © 2005 Society of Chemical Industry [source] Potential high temperature corrosion problems due to co-firing of biomass and fossil fuelsMATERIALS AND CORROSION/WERKSTOFFE UND KORROSION, Issue 10 2008M. Montgomery Abstract Over the past few years, considerable high temperature corrosion problems have been encountered when firing biomass in power plants due to the high content of potassium chloride in the deposits. Therefore, to combat chloride corrosion problems co-firing of biomass with a fossil fuel has been undertaken. This results in potassium chloride being converted to potassium sulphate in the combustion chamber and it is sulphate rich deposits that are deposited on the vulnerable metallic surfaces such as high temperature superheaters. Although this removes the problem of chloride corrosion, other corrosion mechanisms appear such as sulphidation and hot corrosion due to sulphate deposits. At Studstrup power plant Unit 4, based on trials with exposure times of 3000 h using 0,20% straw co-firing with coal, the plant now runs with a fuel mix of 10% straw,+,coal. Based on results from a 3 years exposure in this environment, the internal sulphidation is much more significant than that revealed in the demonstration project. Avedøre 2 main boiler is fuelled with wood pellets,+,heavy fuel oil,+,gas. Some reaction products resulting from the presence of vanadium compounds in the heavy oil were detected, i.e. iron vanadates. However, the most significant corrosion attack was sulphidation attack at the grain boundaries of 18-8 steel after 3 years exposure. The corrosion mechanisms and corrosion rates are compared with biomass firing and coal firing. Potential corrosion problems due to co-firing biomass and fossil fuels are discussed. [source] Low-profile radio frequency identification tag antenna using a trapezoid patch mountable on metallic surfacesMICROWAVE AND OPTICAL TECHNOLOGY LETTERS, Issue 8 2010Horng-Dean Chen Abstract A trapezoid patch antenna, designed for ultra high frequency band radio frequency identification tag mountable on metallic surfaces, is presented in this article. The proposed antenna has a simple and low-profile (0.8 mm thick) structure. The impedance matching can be easily achieved by adjusting the upper-side width and the height of the trapezoid patch. The reading range of the proposed antenna is verified by calculation and measurement, which shows good agreement. Varying antenna size can provide applicable reading range to suit different applications. The results obtained show that the proposed antenna can work efficiently in free space and on metallic objects. © 2010 Wiley Periodicals, Inc. Microwave Opt Technol Lett 52: 1697,1700, 2010; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.25310 [source] | ||||||||||||||||