Home About us Contact
|
Home About us Contact | ||
|
|
||
Methanol Permeability (methanol + permeability)
Selected AbstractsConductivity and Methanol Permeability of Nafion,Zirconium Phosphate Composite Membranes Containing High Aspect Ratio Filler Particles,FUEL CELLS, Issue 4 2009M. Casciola Abstract Gels of exfoliated ,-zirconium phosphate (ZrPexf) in dimethylformamide (DMF) were used to prepare Nafion/ZrPexf composite membranes with filler loadings up to 7,wt.-% by casting mixtures of Nafion 1100 solutions in DMF and suitable amounts of 2,wt.-% ZrP gels in DMF. TEM pictures showed that the ZrPexf particles had aspect ratio of at least 20. All samples were characterised by methanol permeability (P) and through-plane (,thp) and in-plane (,inp) conductivity measurements at 40,°C and 100% RH. The methanol permeability of Nafion membranes containing in situ grown ZrP particles with low aspect ratio (Nafion/ZrPisg) was also determined. The methanol permeability and the swelling behaviour of the composite membranes turned out to be strongly dependent on the filler morphology. As a general trend, both permeability and swelling decreased according to the sequence: Nafion/ZrPisg > Nafion > Nafion/ZrPexf. The maximum selectivity (,thp/P,=,1.4,×,105,S,cm,3,s) was found for the membrane filled with 1,wt.-% ZrPexf: this value is seven times higher than that of Nafion. For the Nafion/ZrPexf membranes, the ratio ,inp/,thp increases with the filler loading, thus indicating that the preferred orientation of the ZrP sheets is parallel to the membrane surface. [source] Modification of Nafion membrane using poly(4-vinyl pyridine) for direct methanol fuel cellPOLYMER INTERNATIONAL, Issue 5 2006Jeon Chan Woong Abstract Perfluorinated membrane such as Nafion (from Du-Pont) has been used as a polymer electrolyte membrane. Nafion 117 membrane, which was usually used as the electrolyte membrane for the polymer electrolyte membrane fuel cell (PEMFC), was modified by using poly(4-vinyl pyridine) (P4VP) to reduce the methanol crossover, which cause fuel losses and lower power efficiency, by the formation of an ionic crosslink structure (sulfonic acid-pyridine complex) on the Nafion 117 surface. Nafion film was immersed in P4VP/N -methyl pyrrolidone (NMP) solution. P4VP weight percent of modified membrane was controlled by changing the concentration of P4VP/NMP solution and the dipping time. P4VP weight percent increased with increasing concentration of dipping solution and dipping time. The thickness of the P4VP layer increased with increasing concentration of dipping solution and dipping time when the concentration of the dipping solution was low. At high P4VP concentration, the thickness of the P4VP layer was almost constant owing to the formation of acid,base complex which interrupted the penetration of P4VP. FTIR results showed that P4VP could penetrate up to 30 µm of Nafion 117 membrane. Proton conductivity and methanol permeability of modified membrane were lower than those of Nafion 117. Both decreased with increasing concentration of dipping solution and dipping time. Methanol permeability was observed to be more dependent on the penetration depth of P4VP. Water uptake of the modified membrane, the important factor in a fuel cell, was lower than that of Nafion 117. Water uptake also decreased with increasing of P4VP weight. On the basis of this study, the thinner the P4VP layer on the Nafion 117 membrane, the higher was the proton conductivity. Methanol permeability decreased exponentially as a function of P4VP weight percent. Copyright © 2006 Society of Chemical Industry [source] Conductivity and Methanol Permeability of Nafion,Zirconium Phosphate Composite Membranes Containing High Aspect Ratio Filler Particles,FUEL CELLS, Issue 4 2009M. Casciola Abstract Gels of exfoliated ,-zirconium phosphate (ZrPexf) in dimethylformamide (DMF) were used to prepare Nafion/ZrPexf composite membranes with filler loadings up to 7,wt.-% by casting mixtures of Nafion 1100 solutions in DMF and suitable amounts of 2,wt.-% ZrP gels in DMF. TEM pictures showed that the ZrPexf particles had aspect ratio of at least 20. All samples were characterised by methanol permeability (P) and through-plane (,thp) and in-plane (,inp) conductivity measurements at 40,°C and 100% RH. The methanol permeability of Nafion membranes containing in situ grown ZrP particles with low aspect ratio (Nafion/ZrPisg) was also determined. The methanol permeability and the swelling behaviour of the composite membranes turned out to be strongly dependent on the filler morphology. As a general trend, both permeability and swelling decreased according to the sequence: Nafion/ZrPisg > Nafion > Nafion/ZrPexf. The maximum selectivity (,thp/P,=,1.4,×,105,S,cm,3,s) was found for the membrane filled with 1,wt.-% ZrPexf: this value is seven times higher than that of Nafion. For the Nafion/ZrPexf membranes, the ratio ,inp/,thp increases with the filler loading, thus indicating that the preferred orientation of the ZrP sheets is parallel to the membrane surface. [source] Radiation Grafted Membranes for Polymer Electrolyte Fuel Cells,FUEL CELLS, Issue 3 2005L. Gubler Abstract The cost of polymer electrolyte fuel cell (PEFC) components is crucial to the commercial viability of the technology. Proton exchange membranes fabricated via the method of radiation grafting offer a cost-competitive option, because starting materials are inexpensive commodity products and the preparation procedure is based on established industrial processes. Radiation grafted membranes have been used with commercial success in membrane separation technology. This review focuses on the application of radiation grafted membranes in fuel cells, in particular the identification of fuel cell relevant membrane properties, aspects of membrane electrode assembly (MEA) fabrication, electrochemical performance and durability obtained in cell or stack tests, and investigation of failure modes and post mortem analysis. The application in hydrogen and methanol fuelled cells is treated separately. Optimized styrene,/,crosslinker grafted and sulfonated membranes show performance comparable to perfluorinated membranes. Some properties, such as methanol permeability, can be tailored to be superior. Durability of several thousand hours at practical operating conditions has been demonstrated. Alternative styrene derived monomers with higher chemical stability offer the prospect of enhanced durability or higher operating temperature. [source] Poly(vinyl alcohol),polyacrylamide blends with cesium salts of heteropolyacid as a polymer electrolyte for direct methanol fuel cell applicationsJOURNAL OF APPLIED POLYMER SCIENCE, Issue 6 2010M. Helen Abstract A class of inorganic,organic hybrid membranes with low methanol permeability characteristics for possible direct methanol fuel cell (DMFC) applications was architected, formulated, and fabricated through the blending of poly(vinyl alcohol) (PVA) and polyacrylamide (PAM) followed by crosslinking with glutaraldehyde (Glu). Cesium salts of different heteropolyacids, including phosphomolybdic acid (PMA), phosphotungstic acid (PWA), and silicotungstic acid (SWA), were incorporated into the polymer network to form corresponding hybrid membrane materials, namely, PVA,PAM,CsPMA,Glu, PVA,PAM,CsPWA,Glu, and PVA,PAM,CsSWA,Glu, respectively (where "Cs" together with a heteropolyacid abbreviation indicates the cesium salt of that acid). All the three hybrid polymer membranes fabricated exhibited excellent swelling, thermal, oxidative, and additive stability properties with desired proton conductivities in the range 10,2 S/cm at 50% relative humidity. A dense network formation was achieved through the blending of PVA and PAM and by crosslinking with Glu, which led to an order of magnitude decrease in the methanol permeability compared to the state-of-the-art commercial Nafion 115 membrane. The hybrid membrane containing CsSWA exhibited a very low methanol permeability (1.4 × 10,8 cm2/s) compared to other membranes containing cesium salt of heteropolyacids such as PMA and PWA. The feasibility of these hybrid membranes as proton-conducting electrolytes in DMFC was investigated, and the preliminary results were compared with those of Nafion 115. The results illustrate the attractive features and suitability of the fabricated hybrid membranes as an electrolyte for DMFC applications. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010 [source] Effect of addition of organic microspheres on proton conductivity property of sulfonated poly(arylene ether sulfone) membraneJOURNAL OF APPLIED POLYMER SCIENCE, Issue 6 2008Cui Liang Abstract Sulfonated poly(arylene ether sulfone) (SPAES)/polystyrene(PS) and SPAES/polystyrene sulfonic acid (PSSA) composite membranes were studied for a proton-exchange membrane used in a fuel cell. PS microspheres were synthesized by emulsion polymerization. PSSA microspheres with 5.3 mmol/g ion-exchange capacity (IEC) were prepared by sulfonation of PS microspheres. The composite membranes were prepared by solution casting. SPAES/PSSA composite membranes showed higher proton conductivity than a SPAES membrane because of the IEC improved by adding PSSA. Although the addition of PSSA also brought about the increase of a methanol permeability, the proton/methanol selectivity defined as the ratio of the proton conductivity to the methanol permeability was improved at low humidity by adding 5 wt % of PSSA microspheres. Differential scanning calorimetry results indicated that the amount of free water varied in the cases of the addition of the two kinds of organic microspheres. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008 [source] Annealing effect of perfluorosulfonated ionomer membranes on proton conductivity and methanol permeabilityJOURNAL OF APPLIED POLYMER SCIENCE, Issue 1 2008Yinghao Luan Abstract Perfluorosulfonated ionomer (PFSI) was synthesized and PFSI membranes were prepared via a solution-cast method and annealed at different temperatures from 150 to 230°C. The annealing effect on water content, proton conductivity, and methanol permeability were reported and discussed. X-ray diffraction and small angle X-ray scattering were used to test the structure of the membranes. It was found that annealing increased the proton conductivity of the membranes because heat-treatment helped to free the sulfonic groups that were buried in the polymer segments and form more organized ionic clusters. Water content and methanol permeability of the annealed membranes decreased with increasing annealing temperature. Simultaneously, annealing induced more compact chain packing structure, which eventually affected the transport of the proton and methanol through these ionomer membranes. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008 [source] Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton-exchange membranes for fuel cellsJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 2 2007Yuhan Li Abstract A novel sulfonated diamine monomer, 2,2,-bis(p -aminophenoxy)-1,1,-binaphthyl-6,6,-disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30,80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film-forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945,0.161 S/cm) at 20,80 °C in liquid water. The membranes exhibited methanol permeability from 9 × 10,8 to 5 × 10,7 cm2/s at 20 °C, which was much lower than that of Nafion (2 × 10,6cm2/s). The copolymers were thermally stable up to 300 °C. The sulfonated polyimide copolymers with 30,60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 222,231, 2007 [source] Permeability and Conductivity Studies on Ionomer-Polysilsesquioxane Hybrid MaterialsMACROMOLECULAR CHEMISTRY AND PHYSICS, Issue 3 2006Chedarampet S. Karthikeyan Abstract Summary: Hybrid materials based on sulphonated poly(ether ether ketone) (SPEEK, ionomer) and (RSiO1.5)n network (polysilsequioxane) were prepared by sol-gel process. Two different precursors namely aminopropyl trimethoxysilane (APTMS) and imidazoleglycidoxypropyl trimethoxysilane (IGPTMS) were utilized to generate (RSiO1.5)n in SPEEK matrix by sol-gel process. 29Si MAS NMR confirmed the formation of RSiO3/2 network structure inside the matrix. Characterisation of the hybrid materials showed lower methanol and water permeability compared to the plain SPEEK. They are therefore promising materials as membranes for direct methanol fuel cells applications. The hybrid material derived from amino group was more effective in decreasing the permeability than the material derived from imidazole group. However, the proton conductivity of the latter was higher than the material derived from amino group. The results indicate that hybrid material prepared from imidazole containing silane is more suitable as a membrane for direct methanol fuel cell than the one prepared from amino carrying silane because it fulfils the two main requirements, namely low methanol permeability and reasonably good proton conductivity. Figure shows a network of silica phase in SPEEK matrix. [source] Partially Sulfonated Polystyrene and Poly(2,6-dimethyl-1,4-phenylene oxide) Blend Membranes for Fuel CellsMACROMOLECULAR RAPID COMMUNICATIONS, Issue 13 2004Bokyung Kim Abstract Summary: Based on Flory,Huggins parameters (,), the miscibility and the effect of morphological change on proton conductivity and methanol permeability of partially sulfonated polystyrene (SPS) and partially sulfonated poly(2,6-dimethyl-1,4-phenylene oxide) (SPPO), having an identical ion exchange capacity, were investigated. When 50 wt.-% of SPPO was blended, both the proton conductivity and methanol permeability had the highest values, which resulted from the change of amorphous domains and the hydrogen bonding between the two ionomers. The proton conductivities, water uptake and methanol permeability for the SPPO/SPS blend membranes studied here. The membranes with 50 wt.-% SPPO clearly showed the greatest increase in these properties. [source] Modification of Nafion membrane using poly(4-vinyl pyridine) for direct methanol fuel cellPOLYMER INTERNATIONAL, Issue 5 2006Jeon Chan Woong Abstract Perfluorinated membrane such as Nafion (from Du-Pont) has been used as a polymer electrolyte membrane. Nafion 117 membrane, which was usually used as the electrolyte membrane for the polymer electrolyte membrane fuel cell (PEMFC), was modified by using poly(4-vinyl pyridine) (P4VP) to reduce the methanol crossover, which cause fuel losses and lower power efficiency, by the formation of an ionic crosslink structure (sulfonic acid-pyridine complex) on the Nafion 117 surface. Nafion film was immersed in P4VP/N -methyl pyrrolidone (NMP) solution. P4VP weight percent of modified membrane was controlled by changing the concentration of P4VP/NMP solution and the dipping time. P4VP weight percent increased with increasing concentration of dipping solution and dipping time. The thickness of the P4VP layer increased with increasing concentration of dipping solution and dipping time when the concentration of the dipping solution was low. At high P4VP concentration, the thickness of the P4VP layer was almost constant owing to the formation of acid,base complex which interrupted the penetration of P4VP. FTIR results showed that P4VP could penetrate up to 30 µm of Nafion 117 membrane. Proton conductivity and methanol permeability of modified membrane were lower than those of Nafion 117. Both decreased with increasing concentration of dipping solution and dipping time. Methanol permeability was observed to be more dependent on the penetration depth of P4VP. Water uptake of the modified membrane, the important factor in a fuel cell, was lower than that of Nafion 117. Water uptake also decreased with increasing of P4VP weight. On the basis of this study, the thinner the P4VP layer on the Nafion 117 membrane, the higher was the proton conductivity. Methanol permeability decreased exponentially as a function of P4VP weight percent. Copyright © 2006 Society of Chemical Industry [source] | ||||||||||