Home About us Contact
|
Home About us Contact | ||
|
|
||
LOI Values (loi + value)
Selected AbstractsBlends of triazine-based hyperbranched polyether with LDPE and plasticized PVCJOURNAL OF APPLIED POLYMER SCIENCE, Issue 1 2007Jyotishmoy Borah Abstract Triazine-based hyperbranched polyether was obtained by earlier reported method and blended with low density polyethylene (LDPE) and plasticized poly(vinyl chloride) (PVC) separately to improve some desirable properties of those linear polymers. The properties like processability, mechanical properties, flammability, etc. of those linear polymers were studied by blending with 1,7.5 phr of hyperbranched polyether. The mechanical properties were also measured after thermal aging and leaching in different chemical media. SEM study indicates that both polymers exhibit homogenous morphology at all dose levels. The mechanical properties like tensile strength, elongation at break, hardness, etc. of LDPE and PVC increase with the increase of dose level of hyperbranched polyether. The flame retardant behavior as measured by limiting oxygen index (LOI) for all blends indicates an enhanced LOI value compared to the polymer without hyperbranched polyether. The processing behavior of both types of blends as measured by solution viscosity and melt flow rate value indicates that hyperbranched polyether acts as a process aid for those base polymers. The effect of leaching and heat aging of these linear polymers on the mechanical properties showed that hyperbranched polyether is a superior antidegradant compared to the commercially used N -isopropyl- N -phenyl p -phenylene diamine. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 648,654, 2007 [source] A novel thermotropic liquid crystalline copolyester containing phosphorus and aromatic ether moity toward high flame retardancy and low mesophase temperatureJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 5 2010Xiang-Cheng Bian Abstract A series of thermotropic liquid crystalline polyesters containing phosphorus and aromatic ether groups (TLCP-AEs) were synthesized from p -acetoxybenzoic acid (p -ABA), terephthalic acid (TPA), 4,4,-oxybis(benzoic acid) (OBBA), and acetylated 2-(6-oxid-6H-dibenz(c,e) (1,2) oxaphosphorin 6-yl) 1,4-benzenediol (DOPO-AHQ). The chemical structure and the properties of TLCP-AEs were characterized by Fourier-transform spectroscopy (FTIR), proton nuclear magnetic resonance spectroscopy (1H NMR), differential scanning calorimetry (DSC), X-ray diffraction (XRD), thermogravimetry analysis (TGA), scanning electronic microscopy (SEM), polarizing optical microscopy (POM), limiting oxygen index, and UL-94 tests, respectively. The results showed that TLCP-AEs had low and broad mesophase temperatures (230,400 °C). TLCP-AEs also showed excellent thermal stability; their 5%-weight-loss temperatures were above 440 °C and the char yields at 700 °C were higher than 45 wt %. All TLCP-AE polyesters exhibited high flame retardancy with a LOI value of higher than 70 and UL-94 V-0 rating. The SEM observation revealed that TLCP-AEs had good fibrillation ability. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1182,1189, 2010 [source] Synergistic Effect of the Charring Agent on the Thermal and Flame Retardant Properties of PolyethyleneMACROMOLECULAR MATERIALS & ENGINEERING, Issue 2 2004Xiao-Ping Hu Abstract Summary: A new charring agent (CA), a derivative of triazines, was synthesized. The flame retardancy and thermal behavior of a new intumescent flame-retardant (IFR) system for PE (PE-IFR) were investigated by limited oxygen index (LOI), UL-94 test, thermogravimetric analysis (TGA), and FTIR spectroscopy. The TG curves shows that the amount of residue of IFR-PE system are largely increased compared to those of PE at temperatures ranging from 350 to 700,°C. The new PE-IFR system can apparently reduce the amount of decomposing products at higher temperatures and promotes the formation of carbonaceous charred layers. It showed a distinct synergistic flame retardant effect (SE) between nitrogen and phosphorus. The flame retardant PE composition was optimized to achieve a LOI value of 31.2 and UL-94 V-0 performance with the synthesized charring agent, ammonium polyphosphate (APP). TG curves of PE, APP, CA, and different PE/CA/APP systems. [source] Flame retardation and thermal degradation of flame-retarded polypropylene composites containing melamine phosphate and pentaerythritol phosphateFIRE AND MATERIALS, Issue 5 2008Shun Zhou Abstract The flame retardation of polypropylene (PP) composites containing melamine phosphate (MP) and pentaerythritol phosphate (PEPA) was characterized by limiting oxygen index (LOI) and UL 94. The morphology of the char obtained from the combustion of the composites was studied by scanning electron microscopy (SEM). The thermal degradation of the composites was investigated using thermogravimetric (TG) analysis and real-time Fourier transform infrared (RTFTIR) spectroscopy. It has been found that the PP composites containing only MP do not show good flame retardancy even at 40% additive level. Compared with the PP/MP binary composites, all the LOI values of the PP/MP/PEPA ternary composites at the same additive loading increase, and UL 94 ratings of the ternary composites at suitable MP/PEPA ratios are raised to V-0 from no rating (PP/MP). The TG and RTFTIR studies indicate that the interaction occurs among MP, PEPA and PP. Copyright © 2008 John Wiley & Sons, Ltd. [source] Effect of boron-containing materials on the flammability and thermal degradation of polyamide 6 composites containing melamineJOURNAL OF APPLIED POLYMER SCIENCE, Issue 5 2010Mehmet Do Abstract Three different boron-containing substances,zinc borate (ZnB), borophosphate (BPO4), and a boron- and silicon-containing oligomer (BSi),were used to improve the flame retardancy of melamine in a polyamide 6 (PA-6) matrix. The combustion and thermal degradation characteristics of PA-6 composites were investigated with the limiting oxygen index (LOI), the UL-94 standard, thermogravimetric analysis (TGA)/Fourier transform infrared (FTIR) spectroscopy, and differential scanning calorimetry (DSC). A slight increase was seen in the LOI values of a sample containing BSi (1 wt %). BPO4 at high loadings showed a V0 rating (indicating the best flame retardancy) and slightly lower LOI values in comparison with samples with only melamine. For ZnB and BSi, glassy film and char formation decreased the dripping rate and sublimation of melamine, and this led to low LOIs. According to the TGA,FTIR results, the addition of boron compounds did not change the decomposition product distribution of melamine and PA-6. The addition of boron compounds affected the flame retardancy by physical means. The TGA data showed that boron compounds and melamine reduced the decomposition temperature of PA-6. According to the DSC data, the inclusion of boron compounds increased the onset temperature of sublimation of melamine and also affected the flame retardancy negatively. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010 [source] Investigation of flame retardancy and physical,mechanical properties of zinc borate/boric acid polyester compositesJOURNAL OF APPLIED POLYMER SCIENCE, Issue 5 2010Miyaser Demirel Abstract The glass fiber reinforced polyester composite materials were prepared with varying contents of boric acid, zinc borate, and magnesium hydroxide as flame retardants to improve the flame retardancy of the composites. Experimental results showed that boric acid exhibited a good flame retardant effect on the polyester composite. When boric acid content is used as 15 wt %, the Limiting Oxygen Index (LOI) value of the composite reached upto 25.3. The increase in boric acid content from 15 to 30 wt %, the LOI values of composite were enhanced from 25.3 to 34.5 by 9.2 units. The LOI values of the composite samples increased with increasing boric acid content. The smoke density results showed that the addition of glass fiber and flame retardants decreased the smoke density of the unreinforced polyester resin. The mechanical properties of the composites have decreased by the addition of flame retardants. The scanning electron micrographs taken from fracture surfaces were examined. The flame retardants, such as boric acid, were well dispersed in the glass fiber reinforced polyester composites and obviously improved the interfacial interaction between glass fibers and polyester composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010 [source] Synthesis of a magnesium/aluminum/iron layered double hydroxide and its flammability characteristics in halogen-free, flame-retardant ethylene/vinyl acetate copolymer compositesJOURNAL OF APPLIED POLYMER SCIENCE, Issue 4 2008Chuan-Mei Jiao Abstract Mg,Al,Fe ternary hydrotalcites were synthesized by a coprecipitation method and characterized with powder X-ray diffraction, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The flame-retardant effects of Mg/Al,CO3 layered double hydroxides (LDHs) and Mg/Al/Fe,CO3 LDHs in an ethylene/vinyl acetate copolymer (EVA) were studied with the limited oxygen index (LOI), the UL-94 test, and the cone calorimeter test (CCT), and the thermal degradation behavior of the composites was examined by thermogravimetric analysis. The results showed that the LOI values of the EVA/(Mg/Al/Fe,CO3 LDH) composites were basically higher than those of the EVA/(Mg/Al,CO3 LDH) composites at the same additive level. In the UL-94 test, there was no rating for the EVA/(Mg/Al,CO3 LDH) composite at the 50% additive level, and a dripping phenomenon occurred. However, the EVA/(Mg/Al/Fe,CO3 LDH) composites at the same loading level of LDHs containing a suitable amount of Fe3+ ion reached the V-0 rating, the dripping phenomenon disappearing. The CCTs indicated that the heat release rate (HRR) of the EVA composites with Mg/Al/Fe,CO3 LDHs containing a suitable amount of Fe3+ decreased greatly in comparison with that of the composites with Mg/Al,CO3 LDHs. The introduction of a given amount of Fe3+ ion into Mg/Al,CO3 LDHs resulted in an increase in the LOI, a decrease in the HRR, and the achievement of the UL-94 V-0 rating. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008 [source] Microencapsulation of ammonium polyphosphate: Preparation, characterization, and its flame retardance in polypropylenePOLYMER COMPOSITES, Issue 8 2008Kun Wu Microencapsulated ammonium polyphosphate (MCAPP) with a melamine,formaldehyde (MF) resin coating layer was prepared by in situ polymerization. MCAPP was characterized by Fourier transform infrared, X-ray photoelectron spectroscopy, and so on. The results show that the microencapsulation with MF resin leads to a decrease in the particles' size and water absorption. The flame retardant action and mechanism of MCAPP and ammonium polyphosphate (APP) in polypropylene are studied using limiting oxygen index (LOI) and UL 94 test, and their thermal stability is evaluated by thermogravimetric analysis. The LOI value of the PP/MCAPP composite at 30 wt% loading is 30.5%, whereas the corresponding value of the PP/APP composite is only 20%. Moreover, the LOI values of the PP/MCAPP/PER composites are higher than the ones of the PP/APP/PER composites. In the UL 94 test, the PP/MCAPP/PER composites with suitable ratios of MCAPP to PER can reach the V-0 rating, and the best rating of the PP/APP/PER composites is V-1. V-1. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers [source] Preparation and characterization of microcapsulated red phosphorus and its flame-retardant mechanism in halogen-free flame retardant polyolefinsPOLYMER INTERNATIONAL, Issue 8 2003Qiang Wu Abstract Microcapsulated red phosphorus (MRP), with a melamine,formaldehyde resin coating layer, was prepared by two-step coating processes. The physical and chemical properties of MRP were characterized by Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy (TEM) and other measurements. The flame retardant action and mechanism of MRP in the halogen-free flame retardant (HFFR) polyolefins (PO) blends have been studied using cone calorimeter, limiting oxygen index (LOI), thermogravimetric analysis (TGA) and dynamic FTIR spectroscopy. The results show that the MRP, which is coated with melamine,formaldehyde resin, has a higher ignition point, a considerably lower amount of phosphine evolution and of water absorption compared with red phosphorus (RP) itself. The data observed by cone calorimeter, LOI and TGA measurements from the PO/HFFR blends demonstrated that the MRP can decrease the heat release rate and effective heat of combustion, and increase the thermostability and LOI values of PO materials. The dynamic FTIR results revealed the flame-retardant mechanism that RP can promote the formation of charred layers with the P,O and P,C complexes in the condensed phase during burning of polymer materials. Copyright © 2003 Society of Chemical Industry [source] Synergistic effects of , -cyclodextrin containing silicone oligomer on intumescent flame retardant polypropylene systemPOLYMERS FOR ADVANCED TECHNOLOGIES, Issue 10 2010Huanfeng Wang Abstract The effects of , -cyclodextrin containing silicone oligomer(CDS), as a synergistic agent, on the flame retardancy and mechanical properties of intumescent flame retardant polypropylene composites were studied by adding different amounts of CDS in intumescent flame retardants. The limiting oxygen index (LOI), UL-94 test, thermogravimetric analysis (TGA), and scanning electron microscopy (SEM) were utilized to evaluate the synergistic effects of CDS in the composites. It was found that after a little amount of CDS partially replaced a charring-foaming agent (CFA) in IFR, LOI values of the composites were enhanced and they obtained a UL-94 V-0 rating. IFR system containing 6.25wt% CDS presented the best flame retardancy in PP. The experimental results obtained from LOI and UL-94, TGA, SEM, and mechanical properties indicated that the combination of CDS and CFA presents synergistic effects in flame retardancy, char formation, and mechanical properties of the composites. This is probably due to different structures of polyhydroxyl macromolecules (CDS and CFA), the existence of dimethyl silicone group in CDS, and the toughness of epoxy silicon chain in CDS. SEM results proved that the interfacial compatibility between IFR and PP was improved by CDS. Copyright © 2009 John Wiley & Sons, Ltd. [source] | ||||||||||