Home About us Contact
|
Home About us Contact | ||
|
|
||
Linear Behavior (linear + behavior)
Selected AbstractsHighlight of a compensation effect between filler morphology and loading on dynamic properties of filled rubbersJOURNAL OF APPLIED POLYMER SCIENCE, Issue 5 2010Franck Sosson Abstract This investigation highlighted the equivalence between carbon black (CB) loading and structure influences on dynamic mechanical properties in the linear behavior of several filled synthetic rubber compounds. Different morphologies (specific surface area and structure) of CB incorporated at different loadings were formulated to modulate the filler-rubber matrix interphase content, usually named "tightly bound rubber." Both reinforcement level and tightly bound rubber content were measured on each compound by dynamic mechanical analysis (DMTA) and by Soxhlet extraction and thermogravimetry (TGA) respectively. Then, a systematic description of their evolution was made against CB loading and morphology. These evolutions were attributed to the hydrodynamic effect which could be evaluated by the effective filler volume fraction. A new parameter , is defined, representing the effective filler volume fraction for each compound and it was calculated on the basis of experimental parameters. Results show good correspondences between , included both the hydrodynamic effects of the filled carbon black rubbers and dynamic mechanical properties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010 [source] Wear in molded tibial inserts: Knee simulator study of H1900 and GUR1050 polyethylenesJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 2 2008Riichiro Tsukamoto Abstract Hi-fax 1900Ô tibial inserts were used in the IB-1 total knee replacement (TKR) beginning 1978, soon followed by the AGC design. Such direct compression molded (DCM) inserts was relatively immune to oxidation. Unfortunately the Hi-fax 1900Ô resin (H1900) was taken off the market in year 2004. As an alternate, GUR1050 was introduced in the VanguardÔ TKR. However there appeared to be little or no wear comparisons of molded inserts. Therefore the study aim was to compare wear performance of GUR1050 to the historical H1900. The hypothesis was that Hi-fax and GUR1050 would show comparable wear performance. The VanguardÔ was a posterior-cruciate sacrificing design (Biomet Inc.). All tibial inserts were sterilized by gamma-radiation (3.2 Mrad) under argon. A 6-channel, displacement,controlled knee simulator was used with serum lubricant (protein concentration 20 mg/mL). Wear assessments were by gravimetric methods and linear regression techniques. The gross weight-loss trends over 2.5 Mc duration demonstrated excellent linear behavior with good agreement between TKR sets (<±10%). Fluid sorption artifacts in control represented less than 5% of gross wear magnitudes. Thus suitable corrections could be made in determining net wear. The H1900 and GUR1050inserts demonstrated net wear-rates of 3.6 and 3.4 mm3/Mc, respectively. This difference was not found to be statistically significant. This wear study demonstrated that GUR1050 inserts were indistinguishable from the Hi-fax 1900 in terms of laboratory wear performance, proving our hypothesis. Given the excellent clinical history of DCM Hi-fax 1900, the GUR1050 should be an ideal candidate for TKR. © 2007 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2008 [source] Reversible addition,fragmentation chain-transfer graft polymerization of styrene: Solid phases for organic and peptide synthesisJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 23 2002Leonie Barner Abstract The ,-initiated reversible addition,fragmentation chain-transfer (RAFT)-agent-mediated free-radical graft polymerization of styrene onto a polypropylene solid phase has been performed with cumyl phenyldithioacetate (CPDA). The initial CPDA concentrations range between 1 × 10,2 and 2 × 10,3 mol L,1 with dose rates of 0.18, 0.08, 0.07, 0.05, and 0.03 kGy h,1. The RAFT graft polymerization is compared with the conventional free-radical graft polymerization of styrene onto polypropylene. Both processes show two distinct regimes of grafting: (1) the grafting layer regime, in which the surface is not yet totally covered with polymer chains, and (2) a regime in which a second polymer layer is formed. Here, we hypothesize that the surface is totally covered with polymer chains and that new polymer chains are started by polystyrene radicals from already grafted chains. The grafting ratio of the RAFT-agent-mediated process is controlled via the initial CPDA concentration. The molecular weight of the polystyrene from the solution (PSfree) shows a linear behavior with conversion and has a low polydispersity index. Furthermore, the loading of the grafted solid phase shows a linear relationship with the molecular weight of PSfree for both regimes. Regime 2 has a higher loading capacity per molecular weight than regime 1. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4180,4192, 2002 [source] Determination of basic azaarenes in aviation kerosene by solid-phase extraction and HPLC-fluorescence detectionJOURNAL OF SEPARATION SCIENCE, JSS, Issue 12 2009Elaine Rocha da Luz Abstract SPE in combination with HPLC and fluorescence detection has been used for sensitive determination of six basic azaarenes (7,8-benzoquinoline, 7,9-dimethylbenz[c]acridine, 9-amino-1,2,3,4-tetrahydroacridine, 9-methylacridine, acridine, and dibenz[a,j]acridine) in aviation kerosene (jet fuel). SPE was performed in a single step using a strong cation exchange sorbent. The HPLC system consisted of C18 column with a selected detection program of optimal ,exc and ,em. A gradient elution with ACN and phosphate buffer (pH 6.5) at a flow rate of 1 mL/min allowed efficient and fast separation of azaarenes within 15 min. The LOD and LOQ values (S/N ratio 3:1 and 10:1, respectively) were between 0.0013 and 0.021 and from 0.0044 to 0.072 ng per injection. The calibration curves showed linear behavior from the LOQ to 250 ,g/L (r2 >0.99). For the spiked concentration of 6.0 ,g/L, recoveries were from 92 to 107% for jet fuel samples, except for 9-amino-1,2,3,4-tetrahydroacridine, which presented 68% recovery. The proposed method was applied to the quantification of those six basic azaarenes in one commercial kerosene and in three aviation kerosene samples. The presence of 7,8-benzoquinoline (up to 3.2 ,g/L) and dibenzo[a,j]acridine (up to 6.3 ,g/L) was confirmed in aviation kerosene. [source] Analysis of protoberberine alkaloids in several herbal drugs and related medicinal preparations by non-aqueous capillary electrophoresisJOURNAL OF SEPARATION SCIENCE, JSS, Issue 1 2005Wen Hua Gao Abstract A simple, rapid, reproducible, and universal non-aqueous capillary electrophoresis method has been developed for the separation and determination of three major active protoberberine alkaloids including berberine, palmatine, and jatrorrhizine within 7 min. The effects of the concentrations of acetic acid and electrolyte, the ratio of organic solvent, and the applied voltage on the separation were investigated. The optimum running buffer was composed of 50 mM ammonium acetate, 0.5% (v/v) acetic acid, and 10% (v/v) acetonitrile in methanol. The applied voltage was 18 kV. The analytes were detected by UV at 214 nm. The linearities between peak areas and the concentrations of the analytes were also investigated, and they exhibit excellent linear behavior over the concentration ranges (correlation coefficients: 0.9975,0.9986). The method was successfully applied to determine the three alkaloids in several families of herbal drugs (Rhizoma Coptidis, Cortex Berberidis, Cortex Phellodendri, Herba Chelidonii,Caulis Mahoniae) and their relevant medicinal preparations for the first time, and the recoveries of the three constituents ranged between 95.6,103.2% for berberine, 97.5,103.3% for palmatine, and 96.1,103.6% for jatrorrhizine. [source] Temperature dependence of thermally-carbonized porous silicon humidity sensorPHYSICA STATUS SOLIDI (A) APPLICATIONS AND MATERIALS SCIENCE, Issue 8 2005M. Björkqvist Abstract Thermal carbonization of porous silicon (PS) at 820 °C under acetylene atmosphere is an appropriate method for humidity sensing purposes. It produces stable and hydrophilic surface still maintaining originally large specific surface area of PS. We report the temperature dependence of various electrical param- eters measured for the thermally-carbonized PS humidity sensor. Capacitance of the sensor in dry air (6 RH%) is almost constant at various temperatures, whereas in higher relative humidity values, the temperature dependence becomes evident. The resistance variation of the sensor is less dependent on RH as the temperature increases. While the capacitance showed linear behavior as a function of temperature, the resistance had a clear non-linear temperature dependence. In order to get information about the effects of frequency on capacitance values, we measured a phase angle and admittance of the sensor as a function of frequency at three different temperatures in low and high humidity. According to these results, it is preferable to operate this sensor construction using low frequency (<1 kHz). (© 2005 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] Temperature dependent high resolution resonant spectroscopy on a charged quantum dotPHYSICA STATUS SOLIDI (B) BASIC SOLID STATE PHYSICS, Issue 4 2009M. Kroner Abstract We present temperature dependent high resolution resonant optical spectroscopy on a single, negatively charged InGaAs quantum dot. We performed laser transmission measurements yielding the natural linewidth of the excitonic ground state transition of a quantum dot in a temperature range from 4.2 K up to 25 K. Here, we describe the linewidth evolution and the temperature induced red shift of the resonance energy with simple models based on the exciton,phonon coupling in the quantum dot. The resonant spectroscopy measurements are complemented with results from non-resonant PL measurements on the very same quantum dot. Here we observe a simple linear behavior of the linewidth according to an effect of a fluctuating environment. (© 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] Metallic bundles of single-wall carbon nanotubes probed by electron spin resonancePHYSICA STATUS SOLIDI (B) BASIC SOLID STATE PHYSICS, Issue 11 2007F. Simon Abstract C59N magnetic fullerenes inside single-wall carbon nanotubes (SWCNTs) are used to probe the density of states (DOS) on the host tubes using electron spin resonance (ESR). The C59N radicals are separated by C60 fullerenes to prevent dimerization and C59N,C60 heterodimers are formed at low temperatures. The electron spin,lattice relaxation time, T1, of the heterodimers is deduced from the homogeneous ESR line-width. The analysis is supported by saturation ESR studies. The inverse of the heterodimer T1 follows a linear behavior in the 20,300 K temperature range, the so-called Korringa law, evidencing a metallic DOS on all tubes in a bundle. (© 2007 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] A nonlinear theoretical model for prediction of mechanical behavior of particulate composites and experimental verification of the model predictionsPOLYMER COMPOSITES, Issue 7 2010A. Ramazani S.A. A model for prediction the stress-strain behavior of particulate composite over wide ranges of filler concentration and composite deformation has been developed through combination of Anderson's and Yilmizer's model. The constitutive equations are extracted from first law of thermodynamic and nonlinear dilatational effects which are produced by filler-matrix debonding process. In addition to nonlinear behavior that has been resulted by filler-matrix debonding and was presented by Yilmizer, the formation and growing of void or cavitations has been also introduced in this model, whereas Anderson's model, most important reason for deviation of linear behavior is filler-matrix debonding and has been indicated by change of modulus. Model predictions for effects of the filler concentration and its particle size and particle size distribution for some matrix-filler systems are compared with related experimental data from literature and some investigated systems in this work. An excellent agreement even better than prediction of Anderson's model between experimental data and model predictions can be observed in most cases especially for some concentrated systems. POLYM. COMPOS., 31:1150,1155, 2010. © 2009 Society of Plastics Engineers [source] Simultaneous determination of six herbal components in intestinal perfusate by high-performance liquid chromatographyBIOMEDICAL CHROMATOGRAPHY, Issue 8 2009Zhanguo Wang Abstract An effective, accurate and reliable HPLC with UV detection method was developed and validated for quantitation of six components: baicalin, berberine hydrochloride, quercetin, kaempferol, isorhamnetin and baicalein in intestinal perfusate using rotundin as an internal standard. The chromatographic separation was performed on a Welchrom-C18 column (250 × 4.6 mm i.d. with 5.0 µm particle size) with a mobile phase consisting of acetonitrile, water, phosphoric acid and triethylamine (30:70:0.2:0.1,v/v) at a flow rate of 1.0 mL/min and a UV detection at 270 nm. The method had a chromatographic run time of 30 min and excellent linear behavior over the investigated concentration ranges observed with the values of r higher than 0.99 for all the analytes. The lower limit of quantification of the analytical method was 0.09 µg/mL for berberine hydrochloride, quercetin, kaempferol and baicalein and 0.18 µg/mL for baicalin and isorhamnetin. The intra- and inter-day precisions measured at three concentration levels were all less than 10% for all analytes. The bias ranged from ,6.91 to 4.33%. The validated method has been successfully applied to investigate the rat intestine absorption profiles of baicalin, berberine hydrochloride, quercetin, kaempferol, isorhamnetin and baicalein. Copyright © 2009 John Wiley & Sons, Ltd. [source] Electrical characteristics of Al/polyindole Schottky barrier diodes.JOURNAL OF APPLIED POLYMER SCIENCE, Issue 5 2009Abstract In this study, the forward and reverse bias current,voltage (I,V), capacitance,voltage (C,V), and conductance,voltage (G/,,V) characteristics of Al/polyindole (Al/PIN) Schottky barrier diodes (SBDs) were studied over a wide temperature range of 140,400 K. Zero-bias barrier height ,B0(I,V), ideality factor (n), ac electrical conductivity (,ac), and activation energy (Ea), determined by using thermionic emission (TE) theory, were shown fairly large temperature dispersion especially at lower temperatures due to surface states and series resistance of Al/PIN SBD. I,V characteristics of the Al/PIN SBDs showed an almost rectification behavior, but the reverse bias saturation current (I0) and n were observed to be high. This high value of n has been attributed to the particular distribution of barrier heights due to barrier height inhomogeneities and interface states that present at the Al/PIN interface. The conductivity data obtained from G/,V measurements over a wide temperature range were fitted to the Arrhenius and Mott equations and observed linear behaviors for ,ac vs. 1/T and ln ,ac vs. 1/T1/4 graphs, respectively. The Mott parameters of T0 and K0 values were determined from the slope and intercept of the straight line as 3.8 × 107 and 1.08 × 107 Scm,1K1/2, respectively. Assuming a value of 6 × 1012 s,1 for ,0, the decay length ,,1 and the density states at the Fermi energy level, N(EF) are estimated to be 8.74 Å and 1.27 × 1020 eV,1cm,3, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009 [source] | ||||||||||||||||