Home About us Contact
|
Home About us Contact | ||
|
|
||
Joint Strength (joint + strength)
Selected AbstractsAutomotive Material Sustainability Through Reversible Adhesives,ADVANCED ENGINEERING MATERIALS, Issue 7 2010Allan R. Hutchinson This communication defines the key existing technologies for reversible adhesion and bonded joint disassembly, and introduces the reader to early experimental findings on the use of thermally labile functional additives in an adhesive matrix. These additives have been found to induce localized, out of plane stresses in a joint's bondline, allowing for an adhesive disbond. It has been found that the additive and adhesive matrix combination is key to the relationship between joint disassembly and joint strength. [source] Fatigue performance of metallic reverse-bent jointsFATIGUE & FRACTURE OF ENGINEERING MATERIALS AND STRUCTURES, Issue 9 2009G. FESSEL ABSTRACT Adhesively bonded lap shear joints have been investigated widely and several ideas have been proposed for improving joint strength by reducing bondline stress concentrations. These include application of adhesive fillets at the overlap ends and use of adhesive with graded properties in the overlap area. Another, less common, approach is to deform the substrates in the overlap area in order to obtain a more desirable bondline stress distribution. Previous work carried out by the authors on a number of different substrate materials indicated that a reverse-bent joint geometry is useful for increasing joint strength. Results from static stress analysis and experimental testing demonstrated that significant improvements could be achieved. This paper presents results of further work carried out to assess the fatigue performance of reverse-bent joints. Substrates with different yield and plastic deformation characteristics were used and the effects of different overlap lengths on strength were examined. The results of this research show that the improvements obtained under static tests conditions translate to even higher benefits in fatigue. The paper also explains the failure mechanism of the joints under fatigue loading. [source] Strength estimation of ceramic,metal joints with various interlayer thicknessFATIGUE & FRACTURE OF ENGINEERING MATERIALS AND STRUCTURES, Issue 5 2003M. TAKAHASHI ABSTRACT Residual stresses generated by the mismatch of thermal expansion coefficients of ceramics and metals affect the strength of ceramic,metal joints. An interlayer metal can be inserted between the ceramic and metal in order to relax this stress. An analysis was carried out of the residual stresses produced during joint-cooling and in 4-point bending tests. The effects of interlayer thickness on ceramic,metal joint strength were then studied by considering a superimposed stress distribution of the residual stress and the bending stress. Finally, joint strength was estimated from fracture mechanics and strength probability analysis by considering the residual stress distribution, defect size and position of pre-existing defects in the ceramic parts. As a result of this study, we suggest an optimum material selection and interlayer thickness for ceramic,metal joint structures. This approach is generally suitable for the design of electrical and mechanical structures. [source] Friction and degradation of rock joint surfaces under shear loadsINTERNATIONAL JOURNAL FOR NUMERICAL AND ANALYTICAL METHODS IN GEOMECHANICS, Issue 10 2001F. Homand Abstract The morpho-mechanical behaviour of one artificial granite joint with hammered surfaces, one artificial regularly undulated joint and one natural schist joint was studied. The hammered granite joints underwent 5 cycles of direct shear under 3 normal stress levels ranging between 0.3 and 4 MPa. The regularly undulated joint underwent 10 cycles of shear under 6 normal stress levels ranging between 0.5 and 5 MPa and the natural schist replicas underwent a monotonics shear under 5 normal stress levels ranging between 0.4 and 2.4 MPa. These direct shear tests were performed using a new computer-controlled 3D-shear apparatus. To characterize the morphology evolution of the sheared joints, a laser sensor profilometer was used to perform surface data measurements prior to and after each shear test. Based on a new characterization of joint surface roughness viewed as a combination of primary and secondary roughness and termed by the joint surface roughness, SRs, one parameter termed ,joint surface degradation', Dw, has been defined to quantify the degradation of the sheared joints. Examinations of SRs and Dw prior to and after shearing indicate that the hammered surfaces are more damaged than the two other surfaces. The peak strength of hammered joint with zero-dilatancy, therefore, significantly differs from the classical formulation of dilatant joint strength. An attempt has been made to model the peak strength of hammered joint surfaces and dilatant joints with regard to their surface degradation in the course of shearing and two peak strength criteria are proposed. Input parameters are initial morphology and initial surface roughness. For the hammered surfaces, the degradation mechanism is dominant over the phenomenon of dilatancy, whereas for a dilatant joint both mechanisms are present. A comparison between the proposed models and the experimental results indicates a relatively good agreement. In particular, compared to the well-known shear strength criteria of Ladanyi and Archambault or Saeb, these classical criteria significantly underestimate and overestimate the observed peak strength, respectively, under low and high normal stress levels. In addition and based on our experimental investigations, we put forward a model to predict the evolution of joint morphology and the degree of degradation during the course of shearing. Degradations of the artificial undulated joint and the natural schist joint enable us to verify the proposed model with a relatively good agreement. Finally, the model of Ladanyi and Archambault dealing with the proportion of total joint area sheared through asperities, as, once again, tends to underestimate the observed degradation. Copyright © 2001 John Wiley & Sons, Ltd. [source] Mechanical strength of laser-welded cobalt,chromium alloyJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 2 2004N. Baba Abstract The purpose of this study was to investigate the effect of the output energy of laserwelding and welding methods on the joint strength of cobalt-chromium (Co-Cr) alloy. Twotypes of cast Co-Cr plates were prepared, and transverse sections were made at the center ofthe plate. The cut surfaces were butted against one another, and the joints welded with alaser-welding machine at several levels of output energy with the use of two methods. Thefracture force required to break specimens was determined by means of tensile testing. For the0.5-mm-thick specimens, the force required to break the 0.5-mm laser-welded specimens atcurrents of 270 and 300 A was not statistically different (p > 0.05) from the results for thenonwelded control specimens. The force required to break the 1.0-mm specimens double-weldedat a current of 270 A was the highest value among the 1.0-mm laser-welded specimens. The results suggested that laser welding under the appropriate conditions improved the jointstrength of cobalt- chromium alloy. © 2004 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 69B: 121,124, 2004 [source] Effect of plasma treatment and electron beam radiations on the strength of nanofilled adhesive-bonded jointsPOLYMER ENGINEERING & SCIENCE, Issue 8 2010H.M.S. Iqbal This investigation highlights the adhesion performance of carbon fiber- and glass fiber-reinforced polyphenylene sulfide when joined by high-performance neat epoxy adhesive and nanofilled epoxy adhesive. A significant increase in the surface energy of these materials is observed after the surface modification with atmospheric plasma treatment. An increase in surface roughness is observed after exposing the surface to plasma. Lap shear testing of untreated and plasma-treated joints is carried out to correlate the improvement in adhesion properties with the joint strength. A considerable increase in joint strength is observed when the surfaces of these materials are modified by atmospheric pressure plasma. There is a further increase in joint strength when the composites are joined by nanofilled epoxy adhesive, and subsequent exposure to electron beam radiations results in minor increase in the joint strength. Finally, the fractured surfaces of the joints are examined and the analysis is performed. POLYM. ENG. SCI., 50:1505,1511, 2010. © 2010 Society of Plastics Engineers [source] | ||||||||||