			Home About us Contact

Interfacial Shear Strength (interfacial + shear_strength)

Distribution by Scientific Domains

Polymers and Materials Science	80%

Selected Abstracts

Increased Interface Strength in Carbon Fiber Composites through a ZnO Nanowire Interphase

ADVANCED FUNCTIONAL MATERIALS, Issue 16 2009
Yirong Lin
Abstract One of the most important factors in the design of a fiber reinforced composite is the quality of the fiber/matrix interface. Recently carbon nanotubes and silicon carbide whiskers have been used to enhance the interfacial properties of composites; however, the high growth temperature degrade the fiber strength and significantly reduce the composite's in-plane properties. Here, a novel method for enhancing the fiber/matrix interfacial strength that does not degrade the mechanical properties of the fiber is demonstrated. The composite is fabricated using low-temperature solution-based growth of ZnO nanowires on the surface of the reinforcing fiber. Experimental testing shows the growth does not adversely affect fiber strength, interfacial shear strength can be significantly increased by 113%, and the lamina shear strength and modulus can be increased by 37.8% and 38.8%, respectively. This novel interface could also provide embedded functionality through the piezoelectric and semiconductive properties of ZnO. [source]

Precooling of the femoral canal enhances shear strength at the cement,prosthesis interface and reduces the polymerization temperature

JOURNAL OF ORTHOPAEDIC RESEARCH, Issue 9 2006
Pang-Hsin Hsieh
Abstract Preheating of the femoral stem in total hip arthroplasty improves the cement,prosthesis bond by decreasing the interfacial porosity. The main concern, however, is the potential thermal osteonecrosis because of an increased polymerization temperature. In this study, the effects of femoral canal precooling on the characteristics of the cement,stem interface were evaluated in an experimental model for three test conditions: precooling of the femoral canal, preheating of the stem (44°C), and a control in which stems were inserted at room temperature without thermal manipulation of the implant, cement, or bone. Compared to the control group, precooling of the femoral canal and preheating of the stem had similar effects on the cement,stem interface, with greater interfacial shear strength and a reduced porosity. Femoral canal precooling also produced a lower temperature at the cement,bone interface. No difference was found in the ultimate compressive strength of bone cement for the three preparation conditions. Based on this laboratory model, precooling of the femoral canal could improve shear strength and porosity at the stem,cement interface, minimize thermal injury, and maintain the mechanical strength of the cement. © 2006 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res [source]

Interfacial strength in short glass fiber reinforced acrylonitrile-butadiene-styrene/polyamide 6 blends

POLYMER COMPOSITES, Issue 3 2010
Nihat Ali Isitman
The purpose of this study is to derive the apparent interfacial shear strength of short glass fiber reinforced acrylonitrile-butadiene-styrene/polyamide 6 (PA6) blends with different PA6 contents. Tensile stress-strain curves and fiber length distributions are utilized within a continuum micromechanics approach which involves a unified parameter for fiber length distribution efficiency represented as a function of strain. The unique combination of predicted micromechanical parameters is capable of accurately reproducing the mechanical response of the composite to applied strain. In this way, the influence of PA6 on interfacial zone is revealed by outcomes of the predictive method and validated by scanning electron microscopy observations. Favored intermolecular interactions in presence of PA6 chains result in the formation of a PA6 sheathing layer on glass fiber surfaces which in turn causes a drop in the apparent interfacial shear strength. The reason behind is shown to be the shift of the fracture zone from fiber/matrix interface to sheathing layer/matrixinterphase. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers [source]

Covalent addition of diethyltoluenediamines onto carbon nanotubes for composite application

POLYMER COMPOSITES, Issue 8 2009
Shiren Wang
Diethyltoluenediamines (DETDA) was grafted to single-walled carbon nanotubes (SWNTs) through diazonium-based addition for improving dispersion and interfacial bonding in SWNT/epoxy nanocomposites. Characterization results of Fourier Transformed Infrared spectroscopy and Raman spectroscopy validated covalent bonding between DETDA and carbon nanotubes. The degree of functionalization was about 4% based on thermo-gravimetric analysis. Interfacial bonding strength was computed in the presence of chemical bonding and the computation results indicated that the interfacial shear strength in the presence of functionalized carbon nanotubes was significantly enhanced. The experimental test revealed that the tensile strength of nanocomposites was enhanced about 23% and Young's modulus about 25%, with 0.5 wt% loading of functionalized-nanotubes. These considerable improvements further verified the load-transfer enhancement in the functionalized-SWNTs/epoxy nanocomposites. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers [source]

Mechanical properties of injection molded long fiber polypropylene composites, Part 1: Tensile and flexural properties

POLYMER COMPOSITES, Issue 2 2007
K. Senthil Kumar
Innovative polymers and composites are broadening the range of applications and commercial production of thermoplastics. Long fiber-reinforced thermoplastics have received much attention due to their processability by conventional technologies. This study describes the development of long fiber reinforced polypropylene (LFPP) composites and the effect of fiber length and compatibilizer content on their mechanical properties. LFPP pellets of different sizes were prepared by extrusion process using a specially designed radial impregnation die and these pellets were injection molded to develop LFPP composites. Maleic-anhydride grafted polypropylene (MA- g -PP) was chosen as a compatibilizer and its content was optimized by determining the interfacial properties through fiber pullout test. Critical fiber length was calculated using interfacial shear strength. Fiber length distributions were analyzed using profile projector and image analyzer software system. Fiber aspect ratio of more than 100 was achieved after injection molding. The results of the tensile and flexural properties of injection molded long glass fiber reinforced polypropylene with a glass fiber volume fraction of 0.18 are presented. It was found that the differences in pellet sizes improve the mechanical properties by 3,8%. Efforts are made to theoretically predict the tensile strength and modulus using the Kelly-Tyson and Halpin-Tsai model, respectively. POLYM. COMPOS., 28:259,266, 2007. © 2007 Society of Plastic Engineers [source]