Home About us Contact
|
Home About us Contact | ||
|
|
||
Inner Wall (inner + wall)
Selected AbstractsThermocapillary-buoyancy flow of silicon melt in a shallow annular poolCRYSTAL RESEARCH AND TECHNOLOGY, Issue 12 2004Y. R. Li Abstract In order to understand the nature of surface spoke patterns on silicon melt in industrial Czochralski furnaces, a series of unsteady three-dimensional numerical simulations were conducted for thermocapillary-buoyancy flow of silicon melt in annular pool (inner radius ri = 15 mm, outer radius ro = 50 mm, depth d = 3 mm). The pool is heated from the outer cylindrical wall and cooled at the inner wall. Bottom and top surfaces either are adiabatic or allow heat transfer in the vertical direction. Results show that a small temperature difference in the radial direction generates steady roll-cell thermocapillary-buoyancy flow. With large temperature difference, the simulation can predict three-dimensional oscillatory flow, which is characterized by spoke patterns traveling in the azimuthal direction. The small vertical heat flux (3 W/cm2) does not have significant effects on the characteristics of this oscillatory flow. Details of the flow and temperature disturbances are discussed and the critical conditions for the onset of the oscillatory flow are determined. (© 2004 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] Capillary modified with covalently attached coating for enhanced CE separation of biopolymersELECTROPHORESIS, Issue 4 2010Yuan He Abstract ,-Gluconolactone was covalently coupled with aminopropyl-derivatized capillary, creating hydrophilic brushes on the inner wall of the capillary. The hydrophilic coating provided suppression of EOF and minimized protein adsorption, resulting in the separation of basic proteins and DNA with efficiencies up to 450,000,plates/m. The intra- and inter-day repeatabilities of the coating referring to the migration times of the four tested proteins were satisfactory with RSD of no more than 1.1 and 1.8% (n=5), respectively. Two hundred consecutive runs were performed with negligible change in migration times and efficiency. [source] A spatially advancing turbulent flow and heat transfer in a curved channelHEAT TRANSFER - ASIAN RESEARCH (FORMERLY HEAT TRANSFER-JAPANESE RESEARCH), Issue 1 2010Koji Matsubara Abstract Direct numerical simulation was performed for a spatially advancing turbulent flow and heat transfer in a two-dimensional curved channel, where one wall was heated to a constant temperature and the other wall was cooled to a different constant temperature. In the simulation, fully developed flow and temperature from the straight-channel driver was passed through the inlet of the curved-channel domain. The frictional Reynolds number was assigned 150, and the Prandtl number was given 0.71. Since the flow field was examined in the previous paper, the thermal features are mainly targeted in this paper. The turbulent heat flux showed trends consistent with a growing process of large-scale vortices. In the curved part, the wall-normal component of the turbulent heat flux was twice as large as the counterpart in the straight part, suggesting active heat transport of large-scale vortices. In the inner side of the same section, temperature fluctuation was abnormally large compared with the modest fluctuation of the wall-normal velocity. This was caused by the combined effect of the large-scale motion of the vortices and the wide variation of the mean temperature; in such a temperature distribution, large-scale ejection of the hot fluid near the outer wall, which is transported into the near inner-wall region, should have a large impact on the thermal boundary layer near the inner wall. Wave number decomposition was conducted for various statistics, which showed that the contribution of the large-scale vortex to the total turbulent heat flux normal to the wall reached roughly 80% inside the channel 135° downstream from the curved-channel inlet. © 2009 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/htj.20275 [source] Shaping ability of ProFile and K3 rotary Ni-Ti instruments when used in a variable tip sequence in simulated curved root canalsINTERNATIONAL ENDODONTIC JOURNAL, Issue 9 2004L. R. Ayar Abstract Aim, To compare the shaping ability of ProFile and K3 rotary Ni-Ti instruments when used in a variable tip sequence in simulated curved root canals with different curvature and radius. Methodology, ProFile or K3 .06 taper instruments were used to prepare simulated canals of 20° curvature and 5 mm radius (n = 10) and 30° curvature and 3 mm radius canals (n = 10) in resin blocks. All canals were prepared to an apical size 40 at 0.5 mm from the canal terminus using a variable tip crown-down sequence. Pre- and postinstrumentation digital images were recorded, and an assessment of the canal shape was determined using a computer image analysis program. The material removal from the inner and outer wall of the canal was measured at 28 measuring points, beginning 0.5 mm from the end-point of the canal and the data compared using the Mann,Whitney U -test. Results, In 20° and 30° canals both instruments significantly removed more (P < 0.05) material on the outer wall than the inner wall in the apical half of the canal. For ProFile files there was no significant difference in the amount of material removed on the outer canal wall between the 20° and 30° canals. However, in the K3 groups significantly more (P < 0.05) outer canal wall was removed in the apical area in 20° canals. When comparing both instruments the results showed that in 20° canals K3 instruments removed more outer and inner canal wall than ProFile instruments (P < 0.05) but that there was no significant difference (P > 0.05) between the instruments in 30° canals. Conclusion, Within the limitation of this study, both rotary nickel-titanium instruments prepared a well-shaped root canal with minimal canal transportation. [source] Experimental investigation into cavity-type inertial separators,a novel technique for development of subcompact circulating fluidized bed boilersINTERNATIONAL JOURNAL OF ENERGY RESEARCH, Issue 14 2005Animesh Dutta Abstract Cavity-type inertial separators developed by GRI (Patent no. 2, 159, 949, Canada, 2002) were tested in a semi-industrial size circulating fluidized bed pilot plant operated at room temperature. Three rows of separators were hung from the roof of the pilot plant where one row was kept inside the riser and the others were kept in the primary separation chamber, located between the back-pass and the riser. Parameters measured were axial pressure drops along the height of the riser, vertical solids flux on the separator walls, lateral outwards solids flux in the riser with and without separator and local temperatures on the separator walls. A net downwards solids flux is on the inner wall of the separators; however, no downwards solids flux is on the outer walls of the separators. Heat transfer coefficients on the outer wall are found higher than those on the inner walls of the separator. It is also found that the presence of inertial separators not only provides additional heat transfer surfaces but also indirectly increases the heat transfer coefficients on the riser wall. Copyright © 2005 John Wiley & Sons, Ltd. [source] A preliminary study on bladder-assisted rotomolding of thermoplastic polymer compositesADVANCES IN POLYMER TECHNOLOGY, Issue 1 2007A. Salomi Abstract In this preliminary work, a new process is examined for manufacturing hollow parts from continuous fiber-reinforced thermoplastic polymer. The new process combines the basic idea of bag forming (or bladder-assisted forming) with the rotation of the mold for the processing of thermoplastic matrix composites. A pressurized membrane is used to compact the composite on the inner wall of a mold, which is placed inside a forced convection oven. The mold is removed from the oven for the cooling stage. The process was initially developed by using a thermoplastic pre-preg obtained using yarns of commingled E-glass fibers with isotactic polypropylene (iPP). A preliminary characterization of the thermoplastic composite showed that the material can be consolidated with pressures as low as 0.01 MPa, which is readily achievable with the process of this study. The design of the mold and membrane was carried out on the basis of both structural analysis of the aluminum shell and thermal analysis of the mold. The mold thickness is of great importance with respect to both the maximum pressure allowed in the process and the overall cycle time. Molding was performed on stacks of three and six layers of yarn, varying the applied pressure between 0.01 and 0.05 MPa and maximum temperature of the internal air between 185°C and 215°C. The composite shells obtained under different processing conditions were characterized in terms of physical and mechanical properties. Mechanical properties comparable with those obtained by compression molding and vacuum bagging were obtained. The maximum values obtained are 12.1 GPa and 290 MPa for the flexural modulus and the flexural strength, respectively. Furthermore, the results obtained show that mechanical properties improve with increasing the pressure during the cycle and with the maximum temperature used in the process. © 2007 Wiley Periodicals, Inc. Adv Polym Techn 26:21,32, 2007; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/adv.20085 [source] Cover Picture: Plasma Process.PLASMA PROCESSES AND POLYMERS, Issue 9 2006Polym. Cover: The photographs show atmospheric pressure plasmas generated by microwave discharges. Relatively high density plasmas are generated in a 1 cm inner diameter quartz tube. The thermal damage of the quartz tube is avoided by the rotating gas flow in line with the inner wall of the quartz tube. The part, which looks silver, is the sidewall of the flat rectangular waveguide. The color of the light emission changes with different working gases. These photographs show the appearances of the emission of Ar, Ar,+,N2, and Ar,+,H2O, from the left. These photographs are offered from the Plasma Laboratory of Musashi Institute of Technology, Tokyo. [source] Enhancing thermal, electrical efficiencies of a miniature combustion-driven thermophotovoltaic systemPROGRESS IN PHOTOVOLTAICS: RESEARCH & APPLICATIONS, Issue 7 2009Yueh-Heng Li Abstract Methods to enhance the thermal and electrical efficiencies through novel design of combustion and thermal management of the combustor in a miniature thermophotovoltaic (TPV) system are proposed, discussed, and demonstrated in this paper. The miniature TPV system consists of a swirling combustor surrounded by GaSb PV cell arrays. The swirl combustor design, along with a heat-regeneration reverse tube and mixing-enhancing porous-medium fuel injection, improves the low illumination and incomplete combustion problems associated with typical miniature TPV systems. A reverse tube is used to enforce swirling flame attachment to the inner wall of the emitter by pushing the swirl recirculation zone back into the chamber and simultaneously redirecting the hot product gas for reheating the outer surface of the emitter. The porous medium fuel injector is used as a fuel/air mixing enhancer and as a flame stabilizer to anchor the flame. The miniature TPV system, using different combustor configurations, is tested and discussed. Results indicate that the proposed swirling combustor with a reverse tube and porous medium can improve the intensity and uniformity of the emitter illumination, and can increase the thermal radiant efficiency. Consequently, the overall thermal efficiency and electrical output of the miniature TPV system are greatly enhanced. Copyright © 2009 John Wiley & Sons, Ltd. [source] Continuous plug-flow bioreactor: Experimental testing with Pseudomonas putida culture grown on benzoateBIOTECHNOLOGY & BIOENGINEERING, Issue 2 2005Yury Voloshin Abstract The goals of this work were to test the feasibility of a continuous plug-flow (PF) bioreactor and to compare the growth in the PF bioreactor to that in a batch bioreactor. A culture of Pseudomonas putida was pumped through a tube made of Teflon with varying residence times. The culture was aerated by pumping of air simultaneously with liquid medium to provide air bubbles along the tubular culture. When the residence time in the PF bioreactor was greater than the time needed to reach the stationary phase in batch mode, the maximum biomass density reached in PF mode was the same as the maximum density reached in the batch bioreactor, and benzoate (the only carbon and energy source) was completely consumed. The drawbacks for practical application of PF were found to be fluctuations of cell concentration in the outflow cultural liquid due to cell aggregation, significant cell adhesion to the inner wall of Teflon tubing, and inadequate aeration. © 2005 Wiley Periodicals, Inc. [source] A new technique for removing the inner wall of Schlemm's canal using cyanoacrylateACTA OPHTHALMOLOGICA, Issue 2 2003Shigeta Naruse Abstract. Purpose:, To introduce a new technique for removing the inner wall of Schlemm's canal using cyanoacrylate. Methods:, Two donor eyes were used in this study. A limbal-based scleral flap was dissected. The external wall of Schlemm's canal was opened and the inner wall of Schlemm's canal was exposed. Ethyl-2-cyanoacrylate was applied uniformly to the inner wall. After it had solidified, it was removed with fine forceps. The operated sites were then studied by light microscopy. Results:, After cyanoacrylate removal, the aqueous humour was seen percolating through the thin remaining trabecular meshwork. Histopathological findings at the operated sites revealed that the lining of the Schlemm's endothelial cells was irregular. Endothelial cell nuclei were rarely seen along the canal wall. Microperforation to the anterior chamber was not seen. Conclusion:, This new technique is potentially a safer method for removing the inner wall of Schlemm's canal than the conventional method. [source] Electroosmotic flow in a poly(dimethylsiloxane) channel does not depend on percent curing agentELECTROPHORESIS, Issue 7-8 2004Aaron R. Wheeler Abstract Poly(dimethylsiloxane) (PDMS) microfluidic devices were prepared from different ratios of "curing agent" (which contains silicon hydride groups) to "base" (which contains vinyl-terminated noncross-linked PDMS), to determine the effect of this ratio on electroosmotic flow (EOF). In fabricating devices for this purpose, a novel method for permanently enclosing PDMS channels was developed. As a supplement to the microfluidic method, the inner walls of capillaries were coated with PDMS formed from varying ratios of curing agent to base. EOF was found to be constant for PDMS formed with each ratio, which implies that the negative surface charges do not arise from chemical species present only in the base or the curing agent. [source] Advances in sol-gel based columns for capillary electrochromatography: Sol-gel open-tubular columnsELECTROPHORESIS, Issue 22-23 2002Abdul Malik Abstract The development of sol-gel open-tubular column technology in capillary electrochromatography (CEC) is reviewed. Sol-gel column technology offers a versatile means of creating organic-inorganic hybrid stationary phases. Sol-gel column technology provides a general approach to column fabrication for microseparation techniques including CEC, and is amenable to both open-tubular and monolithic columns. Direct chemical bonding of the stationary phase to the capillary inner walls provides enhanced thermal and solvent stability to sol-gel columns. Sol-gel stationary phases inherently possess higher surface area, and thus provide an effective one-step alternative to conventional open-tubular column technology. Sol-gel column technology is applicable to both silica-based and transition metal oxide-based hybrid stationary phases, and thus, provides a great opportunity to utilize advanced material properties of a wide range of nontraditional stationary phases to achieve enhanced selectivity in analytical microseparations. A wide variety of stationary phase ligands can be chemically immobilized on the capillary inner surface using a single-step sol-gel procedure. Sol-gel chemistry can be applied to design stationary phases with desired chromatographic characteristics, including the possibility of creating columns with either a positive or a negative charge on the stationary phase surface. This provides a new tool to control electroosmotic flow (EOF) in the column. Column efficiencies on the order of half a million theoretical plates per meter have been reported for sol-gel open-tubular CEC columns. The selectivity of sol-gel stationary phases can be easily fine-tuned by adjusting the composition of the coating sol solution. Open-tubular columns have significant advantages over their packed counterparts because of the simplicity in column making and hassle-free fritless operation. Open-tubular CEC columns possess low sample capacity and low detection sensitivity. Full utilization of the analytical potential of sol-gel open-tubular columns will require a concomitant development in the area of high-sensitivity detection technology. [source] Experimental investigation into cavity-type inertial separators,a novel technique for development of subcompact circulating fluidized bed boilersINTERNATIONAL JOURNAL OF ENERGY RESEARCH, Issue 14 2005Animesh Dutta Abstract Cavity-type inertial separators developed by GRI (Patent no. 2, 159, 949, Canada, 2002) were tested in a semi-industrial size circulating fluidized bed pilot plant operated at room temperature. Three rows of separators were hung from the roof of the pilot plant where one row was kept inside the riser and the others were kept in the primary separation chamber, located between the back-pass and the riser. Parameters measured were axial pressure drops along the height of the riser, vertical solids flux on the separator walls, lateral outwards solids flux in the riser with and without separator and local temperatures on the separator walls. A net downwards solids flux is on the inner wall of the separators; however, no downwards solids flux is on the outer walls of the separators. Heat transfer coefficients on the outer wall are found higher than those on the inner walls of the separator. It is also found that the presence of inertial separators not only provides additional heat transfer surfaces but also indirectly increases the heat transfer coefficients on the riser wall. Copyright © 2005 John Wiley & Sons, Ltd. [source] pH sensor based on polyaniline and aniline,anthranilic acid copolymer films using quartz crystal microbalance and electronic absorption spectroscopyPOLYMERS FOR ADVANCED TECHNOLOGIES, Issue 8 2008M. M. Ayad Abstract The pH sensitivity based on conducting polyaniline (PANI) and copolymer of aniline and o -anthranilic acid (AA) films were studied using quartz crystal microbalance (QCM) technique and UV,Vis spectroscopy. The sensor was constructed from these polymer films coated on the electrode of the QCM. The resonant frequency changes as a function of pH in the range of 2,12 were measured. These changes are quantitative indication of the degree of dedoping or redoping of the polymer films upon the subsequent exposure of the electrode to 0.25,M sulfuric acid and different pH solutions. There are two linear regressions between the frequency change and pH with two different and opposite slopes in the regions from 2 to 9 and 9 to 12. The pH sensitivity of the copolymer film was found to be less than using the PANI film. Thin films of PANI and copolymer, which were chemically polymerized in a sulfuric acid solution, were deposited onto the inner walls of the quartz cuvettes. The UV,Vis absorption spectra of these films were measured in different pH solutions. Relations between the maximum absorption and its wavelength versus pH were constructed. The copolymer film shows some advantages over the PANI film. The difference between the PANI and copolymer films as pH sensors using the QCM and electronic absorption extends from the determination of pKa for both films. Copyright © 2008 John Wiley & Sons, Ltd. [source] Electrochemical Doping of Double-Walled Carbon Nanotubes: An In Situ Raman Spectroelectrochemical StudyCHEMPHYSCHEM, Issue 2 2004Ladislav Kavan Prof. Dr. Nanotubes in electric fields: Electrochemistry of double-walled carbon nanotubes (DWCNTs; see picture) was studied for the first time. The DWCNT was prepared by pyrolysis of fullerene peapods, C60@SWCNTs. Responses to electrochemical doping of outer and inner walls were traced and distinguished by in situ Raman spectroelectrochemistry in the area of radial breathing and tangential displacement modes. [source] | ||||||||||||||||||||||