Home About us Contact
|
Home About us Contact | ||
|
|
||
Implant Technology (implant + technology)
Selected AbstractsImplant Technology and UsabilityARTIFICIAL ORGANS, Issue 8 2008Paul M. Meadows Abstract:, Implanted electrical stimulation technology has changed greatly in the roughly five decades of its existence. Many factors determine the viability of the technology and whether the systems and products developed ultimately go on to help the target patient population. This article describes the successful introduction of an implanted system and the challenges to implanted system development, acceptance, and usability of these systems by the patient and clinical communities. [source] The critical-size supraalveolar peri-implant defect model: characteristics and useJOURNAL OF CLINICAL PERIODONTOLOGY, Issue 11 2006Ulf M. E. Wikesjö Abstract Objective: Novel implant technologies and reconstructive therapies for alveolar augmentation require pre-clinical evaluation to estimate their biologic potential, efficacy, and safety before clinical application. The objective of this report is to present characteristics and use of the critical-size, supraalveolar, peri-implant defect model. Methods: Bilateral extraction of the mandibular premolars was performed in 12 Hound Labrador mongrel dogs following horizontal surgical cut-down of the alveolar ridge approximating 6 mm. Each jaw quadrant received three custom-produced TiUniteÔ, ,4.0 × 10 mm threaded implants placed into osteotomies prepared into the extraction sites of the third and fourth premolars. The implants exhibited a reference notch 5 mm from the implant platform to facilitate surgical placement leaving 5 mm of the implant in a supraalveolar position, and to serve as a reference point in the radiographic, histologic and histometric analysis. The implants were submerged under the mucoperiosteal flaps for primary intention healing. Fluorescent bone markers were administered at weeks 3 and 4 post-surgery, and pre-euthanasia. The animals were euthanized following an 8-week healing interval when block biopsies were collected for analysis. Results: Healing was generally uneventful. The radiographic and histometric evaluations demonstrate the limited osteogenic potential of this defect model. Whereas lingual peri-implant sites exhibited a mean (±SE) bone gain of 0.4±0.1 mm, resorption of the buccal crestal plate resulted in a mean bone loss of 0.4±0.2 mm for an overall osteogenic potential following sham-surgery averaging 0.0±0.1 mm. Overall bone density and bone,implant contact in the contiguous resident bone averaged 79.1±1.1% and 76.9±2.3%, respectively. Conclusion: The results suggest that the critical-size, supraalveolar, peri-implant defect model appears a rigorous tool in the evaluation of candidate technologies for alveolar reconstruction and osseointegration of endosseous oral implants. Limited innate osteogenic potential allows critical evaluation of osteogenic, osteoconductive, or osteoinductive technologies in a challenging clinical setting. [source] Construction of Polyethyleneimine-,-cyclodextrin/pDNA Multilayer Structure for Improved In Situ Gene Transfection,ADVANCED ENGINEERING MATERIALS, Issue 1-2 2010Yan Hu This study reports in situ gene delivery from gene-functionalized poly(D,L -lactic acid) (PDLLA, Mw of around 2.0,×,105,g,mol,1) films, which were constructed via layer-by-layer (LbL) assembly technique with low molecular weight polyethylenimine-,-cyclodextrin (PEI-CD) conjugate and plasmid DNA (pDNA). PEI-CD was characterized by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (NMR), respectively. The buildup of multilayered PEI-CD/pDNA pairs onto PDLLA films was monitored with contact angle measurements and UV,Vis spectrometer, respectively. A sustained release of pDNA from multilayered films was observed for 28,h. The mechanism of in situ gene delivery on PDLLA film was investigated in this study as well. Spherical PEI-CD/pDNA complexes were formed and released following the deconstruction of multilayered films, which was confirmed by transmission electron microscopy (TEM) and gel electrophoresis, respectively. Surface mediated in situ gene transfection was achieved when culturing hepatoma G2 (HepG2) and human embryonic kidney 293 (HEK293) onto PEI-CD/pDNA multilayered films. Furthermore, PEI-CD improved the gene transfection efficiency when compared with that of PEI. Such gene-functionalized biomaterial reported here has potential application in tissue engineering and implant technology. [source] Fabrication of Galactosylated Polyethylenimine and Plasmid DNA Multilayers on poly (D,L -lactic acid) Films for in situ Targeted Gene Transfection,ADVANCED ENGINEERING MATERIALS, Issue 5 2009Yan Hu This study presents surface-mediated targeted in situ gene delivery from gene-tagged poly(D,L -lactic acid) (PDLLA) films, which were fabricated via a layer-by-layer (LbL) assembly technique with galactosylated polyethylenimine (GP) and plasmid DNA (pDNA, pSV-,-galactosidase). A linear growth of GP/pDNA multilayered films was observed. The pDNA was continuously released from multilayered films for over 32,h. The multilayered structure degraded and simultaneously formed GP/pDNA complexes in situ when exposing to a physiological environment. The pDNA was well protected by GP against DNase I digestion within formed GP/pDNA complexes. Our results demonstrated that GP contributes to receptor-mediated targeting for cell uptake and in situ gene transfection. The results reported here are potentially important for gene therapy, surface engineering of biomaterials, tissue engineering and implant technology. [source] Layer-By-Layer Assembly of ,-Estradiol Loaded Mesoporous Silica Nanoparticles on Titanium Substrates and Its Implication for Bone HomeostasisADVANCED MATERIALS, Issue 37 2010Yan Hu Drug-loadingmesoporous silica nanoparticles that serve as a nanoreservoir-type drug-delivery system are successfully attached to titanium substrates via the layer-by-layer assembly technique (see scheme). The obtained structure demonstrates great potential for regulating the biological behaviors of osteoblasts/ steoclasts in order to maintain bone homeostasis. The approach we present here may have wide applications in implant technology, tissue engineering, and regenerative medicine. [source] | |||||||||||||