			Home About us Contact

Hydrophilic Additive (hydrophilic + additive)

Distribution by Scientific Domains

Polymers and Materials Science	75%

Selected Abstracts

Organic Phase PPO Biosensors Prepared by Multilayer Deposition of Enzyme and Alginate Through Avidin-Biotin Interactions

ELECTROANALYSIS, Issue 24 2004
S. Cosnier
Abstract Films of electrogenerated polypyrrole and hydrophilic alginate, both functionalized with biotin moieties, were used to allow for the transfer of polyphenol oxidase activity in organic media. Enzyme electrodes, based on multilayered structures, were protected at the molecular level by the affinity binding of alginate as a hydrophilic additive, and were then transferred into chlorobenzene, dichloromethane, chloroform, ethyl acetate or acetonitrile. The biosensor performance for the detection of catechol at ,0.2,V was investigated, highlighting the main influence of the hydrophobicity of the solvent and, to a lesser extent, the dielectric constant. The effect of the substrate hydrophobicity on the biosensor response was examined in chlorobenzene. [source]

Hydrophilization of polypropylene films by using migratory additives

JOURNAL OF VINYL & ADDITIVE TECHNOLOGY, Issue 2 2007
Siqiang Zhu
Linear and branched hydrophilic additives of various molecular weights (MWs) were extruded with polypropylene (PP) to make blend films. The surface-modifying additives included polyethylene glycol (PEG), hydroxyl-terminated four-arm polyethylene oxide (PEO), and a commercial hydrophilic additive, Irgasurf HL560. Films were extruded by using a twin-screw microcompounder at 200°C, and the resulting film thickness was 100 ,m. Attenuated total reflectance (ATR)-FTIR spectrometry and water contact angle measurements were performed on the film surfaces over time to investigate the additive migration behavior. Although ATR-FTIR detected concentration increases for all additives in the subsurface region, there was no significant improvement in surface hydrophilicity for the PEGs and four-arm PEOs in the same period of time as water contact angles were measured on the surfaces. Among the linear additives, low MW PEG (1 kDa) was found to migrate faster than the high MW varieties. The linear PEG and four-arm PEO with MW higher than 2 kDa did not exhibit significant migration to the surface within a month. Irgasurf was found to change the surface wettability effectively in a relatively short time. J. VINYL ADDIT. TECHNOL., 13:57,64, 2007. © 2007 Society of Plastics Engineers. [source]

Chemical modification of polyethersulfone nanofiltration membranes: A review

JOURNAL OF APPLIED POLYMER SCIENCE, Issue 1 2009
B. Van der Bruggen
Abstract Polysulfone (PS) and poly(ether)sulfone (PES) are often used for synthesis of nanofiltration membranes, due to their chemical, thermal, and mechanical stability. The disadvantage for applying PS/PES is their high hydrophobicity, which increases membrane fouling. To optimize the performance of PS/PES nanofiltration membranes, membranes can be modified. An increase in membrane hydrophilicity is a good method to improve membrane performance. This article reviews chemical (and physicochemical) modification methods applied to increase the hydrophilicity of PS/PES nanofiltration membranes. Modification of poly(ether)sulfone membranes in view of increasing hydrophilicity can be carried out in several ways. Physical or chemical membrane modification processes after formation of the membrane create more hydrophilic surfaces. Such modification processes are (1) graft polymerization that chemically attaches hydrophilic monomers to the membrane surface; (2) plasma treatment, that introduces different functional groups to the membrane surface; and (3) physical preadsorption of hydrophilic components to the membrane surface. Surfactant modification, self-assembly of hydrophilic nanoparticles and membrane nitrification are also such membrane modification processes. Another approach is based on modification of polymers before membrane formation. This bulk modification implies the modification of membrane materials before membrane synthesis of the incorporation of hydrophilic additives in the membrane matrix during membrane synthesis. Sulfonation, carboxylation, and nitration are such techniques. To conclude, polymer blending also results in membranes with improved surface characteristics. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009 [source]