Home About us Contact
|
Home About us Contact | ||
|
|
||
Deposition Conditions (deposition + condition)
Selected AbstractsDiamond Growth on a Si Substrate With Ceramic InterlayersJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 5 2007Y. S. Li Deposition of diamond films on Si substrates precoated with a series of ceramic intermediate layers was examined. The interlayers containing SiC, SiNx, SiCN, TiSiN, and TiAlSiN were prepared by a liquid injection plasma-enhanced chemical vapor deposition (PECVD) method using alkoxide solution precursors. The subsequent diamond synthesis on these coatings was carried out by microwave plasma-assisted CVD (MPCVD) using a H2,1%CH4 mixture. A higher nucleation density of diamond was obtained on these intermediate layers than on the as-polished Si wafer, along with a nonuniform surface distribution of diamond. Diamond powder scratching pretreatment of these interlayers enhanced the nucleation density and promoted the formation of fully uniform diamond films. Particularly, nanocrystalline diamond films were directly generated on TiSiN and TiAlSiN layers under an identical deposition condition that had favored the formation of microcrystalline diamond films on Si wafers and the Si(C,N) interlayers. The mechanism for this difference is attributed primarily to a higher amount of residual amorphous carbon in TiSiN and TiAlSiN layers than that inside Si(C,N) layers. [source] PbS and CdS Quantum Dot-Sensitized Solid-State Solar Cells: "Old Concepts, New Results"ADVANCED FUNCTIONAL MATERIALS, Issue 17 2009HyoJoong Lee Abstract Lead sulfide (PbS) and cadmium sulfide (CdS) quantum dots (QDs) are prepared over mesoporous TiO2 films by a successive ionic layer adsorption and reaction (SILAR) process. These QDs are exploited as a sensitizer in solid-state solar cells with 2,2,,7,7,-tetrakis(N,N -di- p -methoxyphenylamine)-9,9,-spirobifluorene (spiro-OMeTAD) as a hole conductor. High-resolution transmission electron microscopy (TEM) images reveal that PbS QDs of around 3,nm in size are distributed homogeneously over the TiO2 surface and are well separated from each other if prepared under common SILAR deposition conditions. The pore size of the TiO2 films and the deposition medium are found to be very critical in determining the overall performance of the solid-state QD cells. By incorporating promising inorganic QDs (PbS) and an organic hole conductor spiro-OMeTAD into the solid-state cells, it is possible to attain an efficiency of over 1% for PbS-sensitized solid-state cells after some optimizations. The optimized deposition cycle of the SILAR process for PbS QDs has also been confirmed by transient spectroscopic studies on the hole generation of spiro-OMeTAD. In addition, it is established that the PbS QD layer plays a role in mediating the interfacial recombination between the spiro-OMeTAD+ cation and the TiO2 conduction band electron, and that the lifetime of these species can change by around 2 orders of magnitude by varying the number of SILAR cycles used. When a near infrared (NIR)-absorbing zinc carboxyphthalocyanine dye (TT1) is added on top of the PbS-sensitized electrode to obtain a panchromatic response, two signals from each component are observed, which results in an improved efficiency. In particular, when a CdS-sensitized electrode is first prepared, and then co-sensitized with a squarine dye (SQ1), the resulting color change is clearly an addition of each component and the overall efficiencies are also added in a more synergistic way than those in PbS/TT1-modified cells because of favorable charge-transfer energetics. [source] Enhancement of Interconnectivity in the Channels of Pentacene Thin-Film Transistors and Its Effect on Field-Effect Mobility,ADVANCED FUNCTIONAL MATERIALS, Issue 14 2006S. Lee Abstract With the aim of improving the field-effect mobility of transistors by promoting the interconnectivity of the grains in pentacene thin films, deposition conditions of the pentacene molecules using one-step (total thickness of layer 50,nm: 0.1,Å,s,1) and two-step (first layer 10,nm: 0.1,Å,s,1, second layer 40,nm: 4.0,Å,s,1) depositions are controlled. Significantly, it is found that the continuities of the pentacene thin films vary with the deposition conditions of the pentacene molecules. Specifically, a smaller number of voids is observed at the interface for the two-step deposition, which results in field-effect mobilities as high as 1.2,cm2,V,1,s,1; these are higher by more than a factor of two than those of the pentacene films deposited in one step. This remarkable increase in field-effect mobility is due in particular to the interconnectivity of the pentacene grains near the insulator substrate. [source] Correlation equation for predicting filter coefficient under unfavorable deposition conditionsAICHE JOURNAL, Issue 5 2008You-Im Chang Abstract A new correlation equation for predicting the filter coefficient under unfavorable deposition conditions is presented. By adopting the triangular network model of using the Brownian dynamic simulation method, as the sum of four individual deposition mechanisms, e.g., the Brownian diffusion, the DLVO interactions, the gravitational force, and the interception, the correlation equation is obtained by regressing against a broad range of parameter values governing particle deposition in deep bed filtration. The new correlation equation is able to describe previous experimental results well, especially for those submicro particles with significant Brownian motion behavior. © 2008 American Institute of Chemical Engineers AIChE J, 2008 [source] Effects of Individual Layer Thickness on the Microstructure and Optoelectronic Properties of Sol,Gel-Derived Zinc Oxide Thin FilmsJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 3 2008Noureddine Bel Hadj Tahar Zinc oxide (ZnO) thin films were prepared under different conditions on glass substrates using a sol,gel process. The microstructure of ZnO films was investigated by means of diffraction analysis, and plan-view and cross-sectional scanning electron microscopy. It was found that the preparation conditions strongly affected the structure and the optoelectronic properties of the films. A structural evolution in morphology from spherical to columnar growth was observed. The crystallinity of the films was improved and columnar film growth became more dominant as the zinc concentration and the substrate withdrawal speed decreased. The individual layer thickness for layer-by-layer homoepitaxy growth that resulted in columnar grains was <20 nm. The grain columns are grown through the entire film with a nearly unchanged lateral dimension through the full film thickness. The columnar ZnO grains are c -axis oriented perpendicular to the interface and possess a polycrystalline structure. Optical transmittance up to 90% in the visible range and electrical resistivity as low as 6.8 × 10,3·,·cm were obtained under optimal deposition conditions. [source] Recent advances in computational fluid dynamics relevant to the modelling of pesticide flow on leaf surfacesPEST MANAGEMENT SCIENCE (FORMERLY: PESTICIDE SCIENCE), Issue 1 2010C Richard Glass Abstract Increasing societal and governmental concern about the worldwide use of chemical pesticides is now providing strong drivers towards maximising the efficiency of pesticide utilisation and the development of alternative control techniques. There is growing recognition that the ultimate goal of achieving efficient and sustainable pesticide usage will require greater understanding of the fluid mechanical mechanisms governing the delivery to, and spreading of, pesticide droplets on target surfaces such as leaves. This has led to increasing use of computational fluid dynamics (CFD) as an important component of efficient process design with regard to pesticide delivery to the leaf surface. This perspective highlights recent advances in CFD methods for droplet spreading and film flows, which have the potential to provide accurate, predictive models for pesticide flow on leaf surfaces, and which can take account of each of the key influences of surface topography and chemistry, initial spray deposition conditions, evaporation and multiple droplet spreading interactions. The mathematical framework of these CFD methods is described briefly, and a series of new flow simulation results relevant to pesticide flows over foliage is provided. The potential benefits of employing CFD for practical process design are also discussed briefly. © Crown copyright 2009. Reproduced with permission of Her Majesty's Stationery Office. Published by John Wiley & Sons, Ltd. [source] Growth of Co/Cu multilayered thin films by electro-depositionPHYSICA STATUS SOLIDI (A) APPLICATIONS AND MATERIALS SCIENCE, Issue 8 2004Y. Hayashi Abstract Electrochemical method has been applied for preparing Co/Cu multilayered thin films. The layers were electrodeposited after injecting Co and Cu containing solutions in a flow exchanged supporting electrolyte solution. In X-ray diffraction at low angle range a long period peak could be observed, and in the middle angle region a single broad peak showing an average lattice spacing of the film was observed. The electrical resistance showed the properties of Giant Magnetoresistance (GMR). The GMR ratio showed a variation against Cu layer thickness as expected for anti-ferromagnetically coupled films. The maximum GMR ratio obtained in this study was 6.2% at room temperature for the film of [Co 2.0 nm/Cu 1.0 nm]15. Though we need further studies for choosing suitable deposition conditions, the electrodeposition method is a promising method for producing multilayered thin films. (© 2004 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] Structural and defect changes of hydrogenated SiGe films due to annealing up to 600°CPHYSICA STATUS SOLIDI (C) - CURRENT TOPICS IN SOLID STATE PHYSICS, Issue 3-4 2010Petr Sládek Abstract In order to better understand the effects of the hydrogen incorporation on the defects and the disorder in the undoped nano/microcrystalline SiGe:H, we performed a comparative study on samples deposited under different plasma conditions. With variation of the pressure, we were able to change the structure of SiGe:H films. We have used the combination of the infrared spectroscopy, CPM, PDS and thermal desorption measurements to study the thermal dependence of defect density, disorder, as well as hydrogen concentration. The film mechanical properties were tested by depth sensing indentation technique. The results showing a different hydrogen bonding with the change of deposition conditions are interpreted as a whole by terms of the specific local hydrogen bonding environment, related to different growth mechanism. (© 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] Control of composition and structure of ferroelectric oxide thin films grown by pulsed laser depositionPHYSICA STATUS SOLIDI (C) - CURRENT TOPICS IN SOLID STATE PHYSICS, Issue 10 2008Maryline Guilloux-Viry Abstract SrBi2Nb2O9 and KTa1,xNbxO3 high quality thin films were grown by pulsed laser deposition. An accurate optimization of deposition conditions is a prerequisite for the control of composition, mainly according to the high volatility of Bi and K. In order to take benefit of the ferroelectric characteristics for new microelectronic devices, thin films were epitaxially grown on various substrates and seed layers adapted to application requirements. For that purpose metal electrodes and ferroelectric oxides were associated in a planar capacitor geometry or in a coplanar configuration depending on the targeted applications. (© 2008 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] Effect of deposition conditions on the growth rate and electrical properties of ZnO thin films grown by MOCVDPHYSICA STATUS SOLIDI (C) - CURRENT TOPICS IN SOLID STATE PHYSICS, Issue 2 2008K. T. Roro Abstract ZnO thin films have been grown on glass substrates by MOCVD. The effect of deposition conditions such as VI/II molar ratio, DEZn flow rate and total reactor pressure on the growth rate and electrical properties of the films was studied. It is found that the growth rate decreases with an increase in the VI/II molar ratio. This behaviour is ascribed to the competitive adsorption of reactant species on the growth surface. The growth rate increases with an increase in DEZn flow rate, as expected. It is shown that the carrier concentration is independent of the DEZn flow rate. An increase in the total reactor pressure yields a decrease in growth rate. This phenomenon is attributed to the depletion of the gas phase due to parasitic prereactions between zinc and oxygen species at high pressure. (© 2008 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] Structure and Corrosion of Magnetron Sputtered Pure Mg Films on Silicon SubstratesPLASMA PROCESSES AND POLYMERS, Issue S1 2007Michael Störmer Abstract Physical vapor deposition (PVD) was used to prepare pure magnesium coatings on silicon substrates at various argon pressures and deposition angles. The film morphology was observed to depend on the deposition conditions. The approximately 3 µm thick Mg films exhibited columnar growth with voided boundaries and a fiber texture of the basal planes parallel to the substrate surface, which is typical of low temperature deposition. At low pressure and angle, the films were more compact, the surface roughness was lower, the texture was stronger, and the corrosion performance was improved. A free corrosion potential of ,1,735 mV and a corrosion rate of 335 µm per year were determined. [source] Plasma polymerization and deposition of glycidyl methacrylate on Si(100) surface for adhesion improvement with polyimidePOLYMERS FOR ADVANCED TECHNOLOGIES, Issue 10 2001X. P. Zou Abstract Thin polymer films were deposited on Si(100) surfaces by plasma polymerization of glycidyl methacrylate (GMA) under different glow discharge conditions. The FT-IR, X-ray photoelectron spectroscopy (XPS), and amine treatment results suggested that the epoxide functional groups of the deposited films had been preserved to various extents, depending on the plasma deposition conditions. The use of a low radio frequency power (, 5 W) and a relatively high system pressure (100,400 Pa) readily resulted in the deposition of thin films having nearly the same composition of the epoxide functional groups as that of the GMA homopolymer. The plasma-polymerized GMA (PP-GMA) thin films deposited on the Ar plasma-pretreated Si(100) surfaces were retained to a large extent after acetone extraction, suggesting the presence of covalent bonding between the PP-GMA layer and the Si surface. Thermal imidization of the poly(amic acid) precursor of polyimide on the GMA plasma-polymerized Si(100) surface resulted in a strongly adhered polyimide film. The adhesion results further suggested that the GMA polymer had been grafted on the Si(100) surface and the epoxide functional groups had undergone reactive interaction (curing) with the carboxylic and amine groups of the poly(amic acid) during thermal imidization. Copyright © 2001 John Wiley & Sons, Ltd. [source] TiO2 DLAR coatings for planar silicon solar cellsPROGRESS IN PHOTOVOLTAICS: RESEARCH & APPLICATIONS, Issue 1 2003B. S. Richards Abstract In this paper we demonstrate that a double-layer anti-reflection (DLAR) coating can be fabricated using only titanium dioxide (TiO2). Two TiO2 thin films were deposited onto planar silicon wafers using a simple atmospheric pressure chemical vapour deposition (APCVD) system under different deposition conditions. Weighted average reflectances of 6.5% (measured) and 7.0% (calculated) were achieved for TiO2 DLAR coatings in air and under glass, respectively. An increase in the short-circuit current density of , Jsc,=,2.5,mA/cm2 can be expected for an optimised TiO2 DLAR coating when compared with a commercial TiO2 single-layer anti-reflection coating. Copyright © 2003 John Wiley & Sons, Ltd. [source] The investigation of protein adsorption behaviors on different functionalized polymers filmsBIOTECHNOLOGY JOURNAL, Issue 6 2007Zhi-Hong Zhang Dr. Abstract The adsorption of BSA and fibrinogen onto plasma-polymerized di-(ethylene glycol) vinyl ether, allylamine, and maleic anhydride films were investigated in detail by surface plasmon resonance spectroscopy (SPR). The chemical properties of the plasma polymers were initially determined by the plasma deposition conditions during the generation procedure. The analysis of the chemical structure of the films and the refractive index of plasma polymers in aqueous solution was carried out using Fourier transform infrared spectroscopy and waveguide mode spectroscopy, respectively. Using water contact angle measurement, the surface wettability of plasma polymers was also characterized. These properties have a critical influence on the behavior of protein adsorption on the surface of the plasma polymers. Protein adsorption was found to depend not only on the types of functionalized groups, but also on the plasma polymer thickness since the protein molecules penetrate into the plasma polymer network bulk. According to the size of protein molecules in aqueous solution and the amount of adsorbed proteins observed by SPR, the conformational changes of proteins could be deduced. [source] Effect of Substrate Temperature on the Plasma Polymerization of Poly(methyl methacrylate),CHEMICAL VAPOR DEPOSITION, Issue 1 2006B. Casserly Abstract Low-power, plasma-enhanced (PE)CVD together with polymerization of methyl methacrylate (MMA) can be used to deposit thin films of poly(methyl methacrylate) (PMMA) with,minimal loss of functional groups, as shown by Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), and Raman spectrometry (RS). Retention of functional groups decreases with increased substrate temperature, corresponding to decreased deposition rates. From XPS data, the calculated percentage loss of functional groups ranges from 0.9,% to 43.4,%, changing as a function of deposition conditions. RS confirms the presence of C=C bonds in the polymer backbone as a result of scission of the ester group from MMA. The thermal properties of PECVD-produced films from MMA can be tailored by varying the substrate temperature. Onset of thermal decomposition increases with increased substrate temperature by eliminating thermally labile peroxide linkages in the polymer backbone, and by crosslinking that occurs at radical sites generated via scission of functional group bonds. The post-anneal thicknesses of the remaining polymer is of the order of 4,nm or less, indicating that low-power PECVD of PMMA is a viable candidate to act as a sacrificial material for air-gap fabrication. [source] Selectively Deposited Silver Coatings on Gold-Capped Silicon Nanowires for Surface-Enhanced Raman SpectroscopyCHEMPHYSCHEM, Issue 8 2009M. Becker Dr. Abstract Gold caps on silicon nanowires are selectively coated with silver by autometallography (electroless deposition). Changing the conditions of silver deposition, a variety of different coating morphologies can be produced (see figure). The different silver coating morphologies are investigated in terms of their capabilities for surface enhanced Raman scattering (SERS) experiments. Gold caps on silicon nanowires are hemispherical and only a few tens of nanometers in diameter when grown from metal catalysts by the vapor-liquid-solid growth mechanism using chemical vapor deposition. These gold caps are capable of enhancing Raman signals based on the surface-enhanced Raman scattering effect. The Raman signal can be enhanced even further (by at least one order of magnitude) when silver is selectively deposited onto these gold caps by autometallography (electroless deposition). By changing the silver deposition conditions, different coating morphologies can be realized on the gold caps that range from very thin, smooth layers to uneven and extremely rough coatings. The SERS signal enhancement and the spatial homogeneity of the achievable enhancement are compared for the different silver coatings using a model dye molecule. [source] | ||||||||||||||||