Home About us Contact
|
Home About us Contact | ||
|
|
||
Crystalline Drug (crystalline + drug)
Selected AbstractsImproving the dissolution and oral bioavailability of the poorly water-soluble drug aloe-emodin by solid dispersion with polyethylene glycol 6000DRUG DEVELOPMENT RESEARCH, Issue 5 2009Hao-gang Duan Abstract Solid dispersions (SDs) of aloe-emodin (AE) and polyethylene glycol 6000 (PEG6000) with different drug loadings were prepared, characterized by scanning electron microscopy (SEM) and differential scanning calorimetry (DSC) and evaluated for solubility and in vitro release. The oral bioavailability of AE from SD in rats was compared with the crystalline drug. Plasma concentrations of AE were determined by HPLC. After administration of crystalline AE (35,mg·kg,1) in rats, the AUC0-600 and Cmax were 393.6±77.1,mg·min·l,1 and 1.87±0.30,mg·l,1, respectively. For the PEG6000 SD of AE, AUC0-600 and Cmax were boosted to 1310.5±111.9,mg·min·l,1 and 5.86±0.47,mg·l,1, respectively. The results indicated that the oral bioavailability of AE was increased significantly. Simultaneously, the Tmax value of AE for AE crystalline was decreased from 75.6±17.3,min to 44.8±14.8,min for SD. The earlier Tmax for AE from SD indicated the higher extent of absorption for SD due to their improved dissolution rate in rat intestine. This SD approach can therefore be used to enhanced dissolution and bioavailability for poorly water-soluble drugs. Drug Dev Res, 2009. © 2009 Wiley-Liss, Inc. [source] Drug,polymer solubility and miscibility: Stability consideration and practical challenges in amorphous solid dispersion developmentJOURNAL OF PHARMACEUTICAL SCIENCES, Issue 7 2010Feng Qian Abstract Drug,polymer solid dispersion has been demonstrated as a feasible approach to formulate poorly water-soluble drugs in the amorphous form, for the enhancement of dissolution rate and bioperformance. The solubility (for crystalline drug) and miscibility (for amorphous drug) in the polymer are directly related to the stabilization of amorphous drug against crystallization. Therefore, it is important for pharmaceutical scientists to rationally assess solubility and miscibility in order to select the optimal formulation (e.g., polymer type, drug loading, etc.) and recommend storage conditions, with respect to maximizing the physical stability. This commentary attempts to discuss the concepts and implications of the drug,polymer solubility and miscibility on the stabilization of solid dispersions, review recent literatures, and propose some practical strategies for the evaluation and development of such systems utilizing a working diagram. © 2010 Wiley-Liss, Inc. and the American Pharmacists Association J Pharm Sci 99:2941,2947, 2010 [source] The use of three different solid dispersion formulations,melt extrusion, film-coated beads, and a glass thermoplastic system,to improve the bioavailability of a novel microsomal triglyceride transfer protein inhibitorJOURNAL OF PHARMACEUTICAL SCIENCES, Issue 5 2004Geert Verreck Abstract A bioavailable formulation for a water-insoluble microsomal triglyceride transfer protein inhibitor, R103757, was developed using solid dispersion technology. The need for an advanced formulation was tested in the dog by assessing the oral bioavailability of three generic concepts: a tablet (crystalline drug), a capsule (film-coated beads), and an oral solution. These screening studies steered further development in the direction of a solid dispersion. Three solid dispersion platforms were assessed: melt extrusion, film-coated beads, and a glass thermoplastic system. Thermal and spectrophotometric analysis revealed that no crystalline drug was present in any of the formulations. The dissolution profiles of the three dispersion systems showed that release was improved compared with the unmanipulated drug. In addition, stability studies confirmed the physical and chemical integrity of the formulation. A human clinical trial was performed to assess the pharmacokinetics of the three amorphous dispersions. Plasma levels were obtained after single oral administration in both the fasting and fed state. The study indicated that all three approaches improved the bioavailability of R103757 with the glass thermoplastic system providing the best performance. These studies point to the potential usefulness of solid dispersion approaches and expand the possible number of ways to implement these methodologies. © 2004 Wiley-Liss, Inc. and the American Pharmacists Association J Pharm Sci 93:1217,1228, 2004 [source] Characterization of glass solutions of poorly water-soluble drugs produced by melt extrusion with hydrophilic amorphous polymersJOURNAL OF PHARMACY AND PHARMACOLOGY: AN INTERNATI ONAL JOURNAL OF PHARMACEUTICAL SCIENCE, Issue 3 2001Angus Forster Indomethacin, lacidipine, nifedipine and tolbutamide are poorly soluble in water and may show dissolution-related low oral bioavailability. This study describes the formulation and characterization of these drugs as glass solutions with the amorphous polymers polyvinylpyrrolidone (PVP) and polyvinylpyrrolidone-co-vinyl acetate by melt extrusion. The extrudates were compared with physical mixtures of drug and polymer. X-ray powder diffraction, thermal analysis, infrared spectroscopy, scanning electron microscopy, HPLC, moisture analysis and dissolution were used to examine the physicochemical properties and chemical stability of the glass solutions prepared by melt extrusion at a 1:1 drug/polymer ratio. Depending on the temperature used, melt extrusion produced amorphous glass solutions, with markedly improved dissolution rates compared with crystalline drug. A significant physicochemical interaction between drug and polymer was found for all extrudates. This interaction was caused by hydrogen bonding (H-bonding) between the carbonyl group of the pyrrole ring of the polymer and a H-donor group of the drug. Indomethacin also showed evidence of H-bonding when physical mixtures of amorphous drug and PVP were prepared. After storage of the extrudates for 4,8 weeks at 25°C/75% relative humidity (RH) only indomethacin/polymer (1:1) extrudate remained totally amorphous. All extrudates remained amorphous when stored at 25°C/< 10% RH. Differences in the physical stability of drug/polymer extrudates may be due to differences in H-bonding between the components. [source] | ||||||||||