			Home About us Contact

Copolymer Gels (copolymer + gel)

Distribution by Scientific Domains

Polymers and Materials Science	50%

Selected Abstracts

Nanostructured copolymer gels for dsDNA separation by CE

ELECTROPHORESIS, Issue 23 2008
Fen Wan
Abstract Pluronics are triblock copolymers of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) that are able to form many different ordered nanostructures at appropriate polymer concentrations and temperatures in selective solvents. These nanostructured "gels" showed desirable criteria when used as DNA separation media, especially in microchip electrophoresis, including dynamic coating and viscosity switching. A ternary system of F127 (E99P69E99)/TBE buffer/1-butanol was selected as a model system to test the sieving performance of different nanostructures in separating dsDNA by CE. The nanostructures and their lattice constants were determined by small-angle X-ray scattering. Viscosity measurements showed the sol,gel transition phenomena. In addition to the cubic structure, successful electrophoretic separation of dsDNA in 2-D hexagonally packed cylinders was achieved. Results showed that without further optimization, ,X174 DNA,Hae III digest was well separated within 15,min in a 7-cm separation channel, by using F127/TBE/1-butanol gel with a 2-D hexagonal structure. A mechanism for DNA separations by those gels with both hydrophilic and hydrophobic domains is discussed. [source]

Introduction of pH-sensitivity into mechanically strong nanoclay composite hydrogels based on N -isopropylacrylamide

JOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 19 2008
Siddharthya K. Mujumdar
Abstract pH-sensitive nanoclay composite hydrogels based on N -isopropylacrylamide (NIPA) were synthesized by copolymerization with cationic and anionic comonomers. Laponite nanoclay particles served as multifunctional crosslinkers, producing hydrogels with exceptionally high mechanical strengths, as measured by elongation at break. Cationic copolymer gels based on NIPA and dimethylaminoethylmethacrylate were prepared by aqueous free radical polymerization, adopting a procedure reported by Haraguchi (Adv Mater 2002, 14, 1120,1124). Without modification, this technique failed to produce anionic copolymer gels of NIPA and methacrylic acid (MAA), due to flocculation of clay particles. Three methods were conceived to incorporate acidic MAA into nanoclay hydrogels. First, NIPA was copolymerized with sodium methacrylate under dilute conditions, producing hydrogels with good pH-sensitivity but weak mechanical characteristics. Second, NIPA was copolymerized with methyl methacrylate, which was then hydrolyzed to generate acid sidegroups, yielding hydrogels that were much stronger but less pH sensitive. Third, NIPA was copolymerized with MAA following modification of the nanoclay surface with pyrophosphate ions. The resulting hydrogels exhibited both strong pH-sensitivities at 37 °C and excellent tensile properties. Optical transparency changed during polymerization, depending on hydrophobicity of the components. This work increases the diversity and functionality of nanoclay hydrogels, which display certain mechanical advantages over conventionally crosslinked hydrogels. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6630,6640, 2008 [source]

Comparative 1H NMR studies of saturation transfer in copolymer gels and mouse lenses

NMR IN BIOMEDICINE, Issue 6 2010
Koji Nakamura
Abstract Saturation transfer in cross-linked copolymer gels and excised intact and perforating trauma-induced cataract mouse lenses (4- or 8-week-old) were studied using intermolecular cross-relaxation rates (1/TIS(H2O); 1/TIS), monitored with f2 -irradiation at ,8.79, ,4.00, and 7.13,ppm (,H2/2,,,,69,Hz). [1] The 1/TIS(7.13,ppm) vs dry weight [W (%)] profiles for hydrophilic copolymer gels were far steeper than those for hydrophobic copolymer gels, indicating the participation of an amount of bound water and a number of copolymer hydroxyl groups in the saturation transfer process. In contrast, the 1/TIS(,8.79,ppm) vs W (%) profiles exhibited little difference between the hydrophilic and hydrophobic copolymer gels, indicating the major participation of molecular rigidity, i.e. W (%) in the saturation transfer process. [2] The 1/TIS(7.13,ppm) values for cataractous mouse lenses were larger than those for intact lenses, indicating the formation of large, immobile lens protein associates or aggregates containing a sufficient amount of bound water for the saturation transfer. [3] The 1/TIS(7.13,ppm) vs W (%) profiles for the hydrophilic copolymer gels exhibited similar characteristics to the intact and cataractous mouse lenses with regard to the saturation transfer process. Copyright © 2010 John Wiley & Sons, Ltd. [source]

Properties of new nanocomposite triblock copolymer gels based on expandable graphite,

POLYMER ENGINEERING & SCIENCE, Issue 9 2008
Marissa A. Paglicawan
In this work, we investigated the effect of expandable graphite (EG) on the property of triblock copolymer prepared from a poly(styrene- b -(ethylene- co -butylene)- b -styrene) (SEBS) imbibed with an EB-compatible hydrocarbon oil. The rheological properties showed that at a temperature between 30 and 40°C below the gel point, the triblock copolymer gels had a dynamic storage modulus (G,) greater than loss modulus (G,), thereby indicating that at ambient temperature, a physical network is still present in spite of the addition of nanoparticles. Dynamic rheological measurements of the resultant nanocomposite triblock copolymer gels confirmed that the addition of EG affects the linear viscoelastic properties and maximum operating temperature of the parent triblock copolymer gels. The mechanical properties showed only marginal increase, which can be attributed to the poor dispersion that leads to agglomeration of particle into micrometer size stacks, and thus the particles behave only as inorganic fillers. The morphology and X-ray diffraction revealed that the EG used to generate nanocomposite triblock copolymer gels is dispersed generally within the swollen copolymer and/or solvent. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers [source]