Home About us Contact
|
Home About us Contact | ||
|
|
||
Composite Latex (composite + latex)
Selected AbstractsStability and optimum polymerized condition of polysiloxane,polyacrylate core/shell polymerADVANCES IN POLYMER TECHNOLOGY, Issue 3 2010Chengyue Ge Abstract The stable emulsion of core/shell latex with little coagulum (no more than 0.5% in quality relative to total monomers) has been prepared at low temperature with potassium-persulfate (KPS), sodium formaldehyde sulfoxylate (SFS), and 2,2,-azobis(2-(2-imidazolin-2-yl)propane)dihydrochloride (VA-044) as composite initiators by staged emulsion polymerization. Reactive surfactants were used to significantly improve the stability of emulsion. More interestingly, reverse core/shell structure was investigated when the organic silicon was added in the late period of polymerization. The effects of the emulsifier, initiators, dosage of organic silicon, and monomer's content on conversion and graft efficiency were studied in detail. Moreover, the stability of emulsion was investigated by the values of zeta potential (,) and coagulum. More importantly, the thermal performance and stability of PSI/PA composite latex was studied by the glass transition temperature (Tg). The results showed that there are appropriate values for all factors to obtain high conversion, graft efficiency, and excellent stability: The dosage of surfactant was about 0.44 g, the dosage of VA-044 was about 1000 mg kg,1, the dosage of organic silicon was about 15%, and the monomer's content was about 30%. In addition, the introduction of organic silicon improved the Tg. © 2010 Wiley Periodicals, Inc. Adv Polym Techn 29:161,172, 2010; View this article online at wileyonlinelibrary. DOI 10.1002/adv.20182 [source] Developing a hybrid emulsion polymerization system to synthesize Fe3O4/polystyrene latexes with narrow size distribution and high magnetite contentJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 22 2007Longlan Cui Abstract A hybrid emulsion polymerization was formulated for synthesizing Fe3O4/polystyrene composite latex. This system, containing binary droplets that are magnetic (Mag)-droplets with a diameter of 100,200 nm and styrene (St)-droplets with a diameter of 3,4 ,m, was obtained by mixing Mag-miniemulsion and St-macroemulsion. With extremely low surfactants concentration (,critical micelle concentration, CMC), the nucleated loci are selectively controlled in the Mag-droplets, as the result of smaller droplet size and larger surface ratio. Both water-soluble potassium persulfate (KPS) and oil-soluble 2,2,-azobis(2-isobutyronitrile) was adopted to initiate the polymerization. In the presence of KPS, magnetic polystyrene latices with particles size of 60,200 nm, narrow size distribution, and high magnetite content (86 wt % measured by TGA) were attained successfully. The synthesized magnetic Fe3O4/polystyrene latices assembled into well-ordered hexagonal structure in the surface of a carbon supported copper grid. The influence of various parameters on various aspects of the as-synthesized Fe3O4/polystyrene was investigated in detail: type of initiator on composite morphology, feed ratio of Mag-miniemulsion and St-macroemulsion on magnetite content, and hydrophobic agent or amount of surfactant on size and size distribution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5285,5295, 2007 [source] Kinetics of Miniemulsion Polymerization of Styrene in the Presence of OrganoclaysMACROMOLECULAR MATERIALS & ENGINEERING, Issue 6 2008Zhaohui Tong Abstract The impacts of nanoclays on the miniemulsion polymerization kinetics of styrene were studied. It was found that both RP and the fractional conversion decreased upon increasing the organoclay content in the miniemulsion system. In the presence of nanoclay the molecular weight of polystyrene nanoclay composite is lower and the particle size polydispersity of the final composite latex is greater than that of pure styrene miniemulsion polymerization. The effect of the nanoclays is mainly caused by the destabilization of the miniemulsion by the organoclay particles. The increase in the monomer viscosity and the decrease in the diffusion rate of the monomer and the living polymer inside the monomer droplet also accounts for the reduction in the polymerization rate. [source] Particle size effect on the film-forming process of PS/PBA composite latexesPOLYMER COMPOSITES, Issue 9 2010aziye U In this work, the effect of hard particle size and blend ratio on the film formation behavior of hard polystyrene (PS) and soft poly(n -butyl acrylate) (PBA) latex blends was studied by means of steady-state fluorescence and UV,visible techniques in conjunction with atomic force microscopy. Three different sets of latexes were synthesized: PBA latex (diameter 97 nm), pyrene (P)-labeled large PS (LgPS; diameter 900 nm), and small PS (SmPS; diameter 320 nm). Two different series of latex blends (LgPS/PBA and SmPS/PBA) were prepared with varying blend composition at room temperature separately. Films were then annealed at elevated temperatures above glass transition (Tg) temperature of PS. Fluorescence intensity (IP) from P and photon transmission intensity (Itr) were measured after each annealing step to monitor the stages of film formation. The results showed that a significant change occurred in IP and Itr at a certain critical weight fraction (Rc) of PBA. Below Rc, two distinct film formation stages, which are named as void closure and interdiffusion, were seen. However, at PBA concentrations nearer to or above Rc, no film formation can be achieved. Comparing to the LgPS/PBA, the sintering process of SmPS/PBA particles occurred at much lower temperatures. Film formation stages for R < Rc were modeled, and related activation energies were calculated. Void closure (,H) and interdiffusion (,E) activation energies for SmPS/PBA were also found smaller in comparing with LgPS/PBA series. However, ,H and ,E values were not changed much with the blend composition for both series. POLYM. COMPOS., 31:1637,1652, 2010. © 2009 Society of Plastics Engineers [source] | ||||||||||