Home About us Contact
|
Home About us Contact | ||
|
|
||
Channel Height (channel + height)
Selected AbstractsIntegrating an Enzyme-Entrapped Conducting Polymer Electrode and a Prereactor in a Microfluidic System for Sensing GlucoseELECTROANALYSIS, Issue 6 2008Po-Chin Nien Abstract In this study, the flow injection analysis was applied to the enzyme-entrapped electrode on a chip for sensing glucose. The on-chip microelectrode was fabricated by the standard photolithography in clean-room environment and the microfluidic channel height of 100,,m on the chip was formed by poly(dimethylsiloxane). The conducting polymer, poly(3,4-ethylenedioxythiophene), PEDOT, was electropolymerized to entrap the coexisting glucose oxidase (GOD) by cyclic voltammetry (CV). The amount of enzyme entrapped in the matrix measured spectroscopically was about 0.101,U/cm2. At a flow rate of 10,ml/hr, the working electrode (Pt/PEDOT/GOD, WE1) was set at 0.7,V (vs. Ag/AgCl) and sensing of H2O2 was carried out by injecting samples with various concentrations of glucose (Glu). A linear relationship between the sensing current and the glucose concentration, ranging from 1 to 20,mM, was obtained with a sensitivity of 8,nA mm,2 mM,1. The response time and the recovery time were about 30 and 230,s, respectively. For a single-potential test, the oxidation currents of 0.08,mM ascorbic acid (AA) and a blend of 0.08,mM AA and 10,mM Glu reached 31.3% and 145.5%, respectively, when compared with the oxidation current of 10,mM Glu alone. However, when a pre-reactor (WE2) was set at the same potential (0.7,V) before the main enzyme integrated electrode (WE1), the oxidation current for the above mixed solution reached 99.6% of the original one. [source] A basic study on humidity recovery by using micro-porous media (Effects of thermal condition of fluids and geometrical condition of apparatus on transport performance)HEAT TRANSFER - ASIAN RESEARCH (FORMERLY HEAT TRANSFER-JAPANESE RESEARCH), Issue 8 2006Shixue Wang Abstract Using an experimental apparatus to examine the performance of heat and mass transfer between constant-temperature water and dry air through a porous plate having extremely small pores, the effects of the thermal conditions in the fluids and the geometric condition of the apparatus on moisture transport were measured. The effects of water temperature, thickness of the porous plate, and channel height of the flowing air on moisture transport are noticeable. However, the effect of air temperature in the channel inlet on moisture transport is slight. In addition, in order to evaluate the degree of air humidity absorption, a parameter called the moisture absorption rate was introduced. The moisture absorption rate was shown to decrease with increasing air velocity and varies only slightly for a plate thickness of 1 mm and decreases for a plate thickness of 3.5 mm with increasing water temperature. © 2006 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(8): 568,581, 2006; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/htj.20133 [source] Comparative study between parallel and counter flow configurations between air and falling film desiccant in the presence of nanoparticle suspensionsINTERNATIONAL JOURNAL OF ENERGY RESEARCH, Issue 8 2003A. Ali Abstract A comparative numerical study is employed to investigate the heat and mass transfer between air and falling film desiccant in parallel and counter flow configurations. Nanoparticles suspensions are added to the falling film desiccant to study heat and mass transfer enhancements. The numerical results show that the parallel flow channel provides better dehumidification and cooling processes of the air than counter flow configuration for a wide range of pertinent parameters. Low air Reynolds number enhances the dehumidification and cooling rates of the air and high air Reynolds number improves the regeneration rate of the liquid desiccant. An increase in the channel height results in enhancing the dehumidification and cooling processes of air and regeneration rate of liquid desiccant. The dehumidification and cooling rates of air are improved with an increase in the volume fraction of nanoparticles and dispersion factor. Copyright © 2003 John Wiley & Sons, Ltd. [source] Concentration polarization in a narrow reverse osmosis membrane channelAICHE JOURNAL, Issue 1 2010Lianfa Song Abstract Concentration polarization in a narrow reverse osmosis channel is bounded by the channel height and under the influence of variable transverse velocity. An attempt was made in this article to quantify concentration polarization in such a narrow membrane channel. The transverse velocity in the membrane channel was first determined and its impact on concentration polarization was investigated. Based on the concept of retained salt, analytical equations were developed for the wall salt concentration at an arbitrary point in the narrow membrane channel. Finally, development of concentration polarization in typical reverse osmosis channels under various conditions was numerically simulated and discussed. Interesting results on the details of concentration polarization in the narrow reverse osmosis channel that had never been reported before were revealed with this mechanistic model. © 2009 American Institute of Chemical Engineers AIChE J, 2010 [source] Optimization of a multiphase sensor for detection of phosphonates in airAICHE JOURNAL, Issue 1 2010Chelsea N. Monty Abstract The objective of this article is to report the modeling and optimization of a new MEMS-based phosphonate sensor that utilizes a porous membrane between a gas and a liquid stream to allow operation at low-liquid and high-gas flow rates. Previous work from our laboratory demonstrated that phosphonate molecules can be detected with such a device, but the sensitivity was insufficient for certain applications (e.g., detection of pesticides in foodstuffs). In this article, COMSOL simulations and design of experiments were used to optimize the device. We find that both the simulation and the experiment show that (i) the size of the pores in the membranes and (ii) the liquid channel height make the most difference to the sensor response. Also, by optimizing the geometry, the sensitivity of the device could be enhanced. The optimized device can detect 109 molecules with good signal to noise. © 2009 American Institute of Chemical Engineers AIChE J, 2010 [source] Application of the Radial Basis Neural Network to Optimization of a MicromixerCHEMICAL ENGINEERING & TECHNOLOGY (CET), Issue 7 2007A. Ansari Abstract The radial basis neural network (RBNN) method has been applied to shape optimization of a staggered herringbone groove micromixer using three-dimensional Navier-Stokes analysis. The calculation of the variance of the mass fraction at various nodes on a plane in the channel is used to quantify the mixing. Optimization techniques based on the RBNN method are used to optimize the shape of the grooves on a single wall of the channel. Three design variables, i.e., the ratio of the groove depth to channel height, the ratio of the groove width to groove pitch, and the angle of the groove, are selected for optimization. The mixing index at the end of the patterned groove is employed as the objective function. The dependence of the objective function on the design variables is analyzed. The RBNN method is successfully applied to improve the degree of mixing with modification of the groove shape. [source] | |||||||||||||