|
| ||
|
|
||
CE Separation (ce + separation)
Selected AbstractsMicrofluidic chip-capillary electrophoresis for two orders extension of adjustable upper working range for profiling of inorganic and organic anions in urineELECTROPHORESIS, Issue 18 2010Wen Peng Guo Abstract To meet the need for onsite monitoring of urine anions, a microfluidic chip-capillary electrophoresis device was designed, fabricated and tested to extend the upper CE working range for an enhancement up to 500 fold (100 fold for sample dilution and 5 folds for CE injection) in order to analyze highly variable anionic metabolites in urine samples. Capillaries were embedded between two PMMA plates with laser-fabricated microchannel patterns to produce the microfluidic chip-capillary electrophoresis to perform standard/sample dilution and CE injection with adjustable dilution ratios. A circular ferrofluid valve was incorporated on-chip to perform cleanup and conditioning, mixing and dilution, injection and CE separation. Under optimized conditions, a complete assay for four samples can be achieved within an hour for 15 anions commonly found in urines. Satisfactory working ranges (0.005,500,mM) and low detection limits (0.5,6.5,,M based on S/N =2) are obtained with satisfactory repeatability (RSD, n=5) 0.52,0.87% and 4.1,6.5% for migration time and peak area, respectively. The working ranges with two orders adjustable upper extension are adequate to cover all analytes concentrations commonly found in human urine samples. The device fabricated shows sufficiently large experimentally verifiable enhancement factor to meet the application requirements. Its reliability was established by more than 94% recoveries of spiked standards and agreeable results from parallel method comparison with conventional ion chromatography method. The extension of the upper CE working range enables flexible onsite dilution on demand, a quick turn-around of results, and a low-cost device suitable for bedside monitoring of patients under critical conditions for metabolic disorders. [source] Microfluidic devices for electrokinetic sample fractionationELECTROPHORESIS, Issue 15 2010Zhen Wang Abstract We present three generations of microchip-based "in-space" sample fractionators and collectors for use in proteomics. The basic chip design consisted of a single channel for CE separation of analytes that then intersects a fractionation zone feed into multiple high aspect ratio microchannels for fractionation of separated components. Achievements of each generation are discussed in relation to important design criteria. CE-separated samples were electrokinetically driven to multiple collection channels in sequence without cross-contamination under the protection of sheath streams. A 36-channel fractionator demonstrated the efficacy of a high-throughput fractionator with no observed cross-contamination. A mixture of IgG and BSA was used to test the efficiency of the fractionator and collector. CE of the fractionated samples was performed on the same device to verify their purity. Our demonstration proved to be efficient and reproducible in obtaining non-contaminated samples over 15 sample injections. Experimental results were found to be in close agreement with PSpice simulation in terms of flow behavior, contamination control and device performance. The design presented here has a great potential to be integrated in proteomic platforms. [source] CE-ESI-MS/MS as a rapid screening tool for the comparison of protein,ligand interactionsELECTROPHORESIS, Issue 7 2010Thomas Hoffmann Abstract In drug development, the combinatorial synthesis of drug libraries is common use, therefore efficient tools for the characterization of drug candidates and the extent of interaction between a drug and its target protein is a central question of analytical interest. While biological activity is tested today by enzyme assays, MS techniques attract more and more attention as an alternative for a rapid comparison of drug,target interactions. CE enables the separation of proteins and drug,enzyme complexes preserving their physiological activity in aqueous media. By hyphenating CE with ESI-MS/MS, the binding strength of enzyme inhibitors can be deduced from MS/MS experiments, which selectively release the inhibitor from the drug,target complex after CID. In this study, ,-chymotrypsin (CT), a serine protease, was chosen as a model compound. Chymostatin is a naturally occurring peptide aldehyde binding to CT through a hemiacetal bond and electrostatic interaction. First, a CE separation was developed, which allows the analysis of ,-CT and a chymotrypsin,chymostatin complex under MS-compatible conditions. The use of neutral-coated CE capillaries was mandatory to reduce analyte,wall interactions. ESI-quadrupole ion trap-MS was worked out to demonstrate the selective drug release after CID. Fragmentation of the drug,enzyme complex was monitored in dependence from the excitation energy in the ion trap, leading to the V50 voltage that enables 50% complex fragmentation as a reference value for chymotrypsin,chymostatin complex. A stable CE-ESI-MS/MS setup was established, which preserves the drug,enzyme complexes during ionization,desolvation processes. With this optimized setup, different CT inhibitors could be investigated and compared. [source] Capillary modified with covalently attached coating for enhanced CE separation of biopolymersELECTROPHORESIS, Issue 4 2010Yuan He Abstract ,-Gluconolactone was covalently coupled with aminopropyl-derivatized capillary, creating hydrophilic brushes on the inner wall of the capillary. The hydrophilic coating provided suppression of EOF and minimized protein adsorption, resulting in the separation of basic proteins and DNA with efficiencies up to 450,000,plates/m. The intra- and inter-day repeatabilities of the coating referring to the migration times of the four tested proteins were satisfactory with RSD of no more than 1.1 and 1.8% (n=5), respectively. Two hundred consecutive runs were performed with negligible change in migration times and efficiency. [source] Direct chiral analysis of primary amine drugs in human urine by single drop microextraction in-line coupled to CEELECTROPHORESIS, Issue 16 2009Kihwan Choi Abstract Three-phase single drop microextraction (SDME) was in-line coupled to chiral CE of weakly basic amine compounds including amphetamine. SDME was used for the matrix isolation and sample preconcentration in order to directly analyze urine samples with the minimal pretreatment of adding NaOH. A small drop of an acidic aqueous acceptor phase covered with a thin layer of octanol was formed at the tip of a capillary by simple manipulation of the liquid handling functions of a commercial CE instrument. While the saline matrix of the urine sample was blocked by the octanol layer, the basic analytes in a basic aqueous donor phase were concentrated into the acidic acceptor drop through the octanol layer by the driving force of the pH difference between the two aqueous phases. The enantiomers of the enriched amines were resolved by using (+)-(18-crown-6)-tetracarboxylic acid as a chiral selector for the subsequent CE separation. From 10,min SDME with the agitation of the donor phase by a small stirrer retrofit to the CE instrument, enrichment factors were about a 1000-fold, yielding the LOD of 0.5,ng/mL for amphetamine. This low LOD value as well as the convenience of in-line coupled SDME make the proposed scheme well suited for the demanding chiral analysis of amphetamine-type stimulants. [source] Comparative metabolite profiling of carboxylic acids in rat urine by CE-ESI MS/MS through positively pre-charged and 2H-coded derivatizationELECTROPHORESIS, Issue 22 2008Wen-Chu Yang Abstract A new approach to the selective comparative metabolite profiling of carboxylic acids in rat urine was established using CE-MS and a method for positively pre-charged and 2H-coded derivatization. Novel derivatizing reagents, N -alkyl-4-aminomethyl-pyridinum iodide (alkyl=butyl, butyl-d9 or hexyl), containing quaternary amine and stable-isotope atoms (deuterium), were introduced for the derivatization of carboxylic acids. CE separation in positive polarity showed high reproducibility (0.99,1.32% RSD of migration time) and eliminated problems with capillary coating known in CE-MS anion analyses. Essentially complete ionization and increased hydrophobicity after the derivatization also enhanced MS detection sensitivity (e.g. formic acid was detected at 0.5,pg). Simultaneous derivatization of one sample using two structurally similar reagents, N -butyl-4-aminomethyl-pyridinum iodide (BAMP) and N -hexyl-4-aminomethyl-pyridinum iodide, provided additional information for recognizing a carboxylic acid in an unknown sample. Moreover, characteristic fragmentation acquired by online CE-MS/MS allowed for identification and categorization of carboxylic acids. Applying this method on rat urine, we found 59 ions matching the characteristic patterns of carboxylic acids. From these 59, 32 ions were positively identified and confirmed with standards. For comparative analysis, 24 standard carboxylic acids were derivatized by chemically identical but isotopically distinct BAMP and N -butyl-d9-4-aminomethyl-pyridinium iodide, and their derivatization limits and linearity ranges were determined. Comparative analysis was also performed on two individual urine samples derivatized with BAMP and N -butyl-d9-4-aminomethyl-pyridinium iodide. The metabolite profiling variation between these two samples was clearly visualized. [source] Competitive immunoassay by capillary electrophoresis with laser-induced fluorescence for the trace detection of chloramphenicol in animal-derived foodsELECTROPHORESIS, Issue 16 2008Can Zhang Abstract A competitive immunoassay using CE with an LIF detector was developed for the detection of chloramphenicol (CAP). The method was based on the competitive reactions between fluorescently labeled CAP hapten and free CAP, with a limited amount of anti-CAP antibody. The poly(N -isopropylacrylamide) (pNIPA) hydrogel was added in the separation buffer as a dynamic modifier to reduce adsorption and enhance reproducibility. The linear range and LOD for CAP were 0.008,5,,g/L and 0.0016,,g/L, respectively. An ELISA using the same immuno-reagents was also developed for the analysis of CAP, with an LOD of 0.03,,g/L. The sensitivity of this CE immunoassay (CEIA)-LIF was almost 20 times greater than that of the ELISA. Using CEIA-LIF, equilibrium was reached in 15,min and the analytical results were obtained within 5,min by CE separation. Sample preparation for CEIA-LIF was not time-consuming and the matrix effect was easy to remove. An LOD of 0.1,,g/kg CAP in food matrices was easily achieved. This method is thus proposed as a fast and sensitive means of detecting trace amounts of CAP residues in animal-derived foods. [source] Analyses of alkaloids in different products by NACE-MSELECTROPHORESIS, Issue 22 2007Chen-Wen Chiu Abstract A simple method for the separation and characterization of five nicotine-related alkaloids by NACE employing UV and MS detections is described here for the first time. Several factors, including NACE parameters (compositions of running solution) and MS parameters (such as nature and flow rate of sheath liquid, pressure of nebulization gas, and flow rate of dry gas), were optimized in order to obtain both an adequate CE separation and high MS signals for the alkaloid compounds used in this study. A reliable CE separation of five alkaloids was achieved in 50,mM ammonium formate that was dissolved in an ACN/methanol mixture (50:50, v/v) of pH*,4.0 (apparent pH 4.0). The optimal electrospray MS measurement was carried out in the positive ionization mode using a coaxial sheath liquid composed of isopropyl alcohol and water in the ratio of 80:20 v/v at a flow rate of 180,,L/h. In addition, the proposed NACE method was also applied in the analyses of alkaloids in several products including chewing gums, beverages, and tobaccos. This NACE-MS method was found to provide a better detection ability and separation resolution for the analysis of nicotine alkaloids when compared to other aqueous CE-MS reports. [source] Study on the enhancement of Ru(bpy)32+ electrochemiluminescence by nanogold and its application for pentoxyverine detectionELECTROPHORESIS, Issue 23 2005Yingju Liu Abstract In this work, CE separation with end-column Ru(bpy)32+ ECL detection for the quantitative determination of pentoxyverine was firstly performed. The experimental conditions, such as the applied potential, injection voltage, injection time, and the pH of separation buffer, were discussed in detail. Gold nanoparticles were found to enhance the ECL intensity at an appropriate volume ratio of nanogold with Ru(bpy)32+ but without changing their nanoproperties proved by transmission electron microscopy (TEM) and UV-vis spectra. The detection limits with or without nanogold were 6,nM and 0.6,,M, respectively. Successful separation of pentoxyverine, chlorpheniramine, and lidocaine was achieved. This method was also applied to monitor drug binding with HSA, and the binding constant for pentoxyverine was estimated as 1.8×103/M. [source] Simultaneous electrochemical and electrochemiluminescence detection for microchip and conventional capillary electrophoresisELECTROPHORESIS, Issue 3 2005Haibo Qiu Abstract A simultaneous electrochemical (EC) and electrochemiluminescence (ECL) detection scheme was introduced to both microchip and conventional capillary electrophoresis (CE). In this dual detection scheme, tris(2,2'-bipyridyl)ruthenium(II) (Ru(bpy)32+) was used as an ECL reagent as well as a catalyst (in the formation of Ru(bpy)33+) for the EC detection. In the Ru(bpy)32+ -ECL process, Ru(bpy)33+ was generated and then reacted with analytes resulting in an ECL emission and a great current enhancement in EC detection due to the catalysis of Ru(bpy)33+. The current response and ECL signals were monitored simultaneously. In the experiments, dopamine and three kinds of pharmaceuticals, anisodamine, ofloxacin, and lidocaine, were selected to validate this dual detection strategy. Typically, for the EC detection of dopamine with the presence of Ru(bpy)32+, a ,5 times higher signal-to-noise ratio (S/N) can be achieved than that without Ru(bpy)32+, during the simultaneous EC and ECL detection of a mixture of dopamine and lidocaine using CE separation. The results indicated that this dual EC and ECL detection strategy could provide a simple and convenient detection method for analysis of more kinds of analytes in CE separation than the single EC or ECL detection alone, and more information of analytes could be achieved in analytical applications simultaneously. [source] Determination of galanthamine in Bulbus Lycoridis Radiatae by coupling capillary electrophoresis with end-column electrochemiluminescence detectionJOURNAL OF SEPARATION SCIENCE, JSS, Issue 15 2010Biyang Deng Abstract A novel method for the determination of galanthamine (GAL) in Bulbus Lycoridis Radiatae has been developed based on coupling CE with an end-column tris(2,2,-bipyridyl)ruthenium(II) electrochemiluminescence (ECL). Parameters affecting CE separation and ECL detection were investigated and optimized. Baseline separation of GAL from other components in the Bulbus Lycoridis Radiatae sample was achieved with an 18,mmol/L phosphate running buffer at pH 9.0. Under the optimized conditions: 12,kV CE-separation voltage, ECL detection potential at 1.25,V with 5,mmol/L and 50,mmol/L phosphate buffer at pH 7.5 in the detection reservoir, the linear range of GAL concentration was from 0.8,ng/mL to 2,,g/mL, whereas the detection limit was 0.25,ng/mL (S/N=3). The proposed method was successfully demonstrated for the determination of GAL in Bulbus Lycoridis Radiatae. [source] Capillary electrophoretic separation and fractionation of hydrophobic peptides onto a pre-structured matrix assisted laser desorption/ionization target for mass spectrometric analysisJOURNAL OF SEPARATION SCIENCE, JSS, Issue 2 2006Johan Jacksén Abstract A CE separation of hydrophobic peptides followed by fractionation onto a prestructured MALDI target and off-line MS analysis was performed. An improved and partially automated manufacturing procedure of the previously described MALDI target is presented. This target is structurally coated with silicone and especially developed for hydrophobic peptides and proteins. Here, the target plate was designed specifically for the CE fraction collection. Different solvents were evaluated to meet the requirements of peptide solubility and compatibility to both the CE and MALDI methods and to the fractionation procedure. CE-MALDI-MS analysis of nine highly hydrophobic peptides from cyanogen bromide-digested bacteriorhodopsin is demonstrated. [source] Simultaneous determination of methylephedrine and pseudoephedrine in human urine by CE with electrochemiluminescence detection and its application to pharmacokeineticsBIOMEDICAL CHROMATOGRAPHY, Issue 11 2009Yan-Ming Liu Abstract A novel method for the determination of ephedra alkaloids (methylephedrine and pseudoephedrine) was developed by electrophoresis capillary (CE) separation and electrochemiluminesence detection (ECL). The use of ionic liquid (1-butyl-3-methylimidazolium tetrafluoroborate, BMIMBF4) improved the detection sensitivity markedly. The conditions for CE separation, ECL detection and effect of ionic liquid were investigated in detail. The two ephedra alkaloids with very similar structures were well separated and detected under the optimum conditions. The limits of detection (signal-to-noise ratio = 3) in standard solution were 1.8 × 10,8 mol/L for methylephedrine (ME) and 9.2 × 10,9 mol/L for pseudoephedrine (PSE). The limits of quantitation (signal-to-noise ratio = 10) in human urine samples were 2.6 × 10,7 mol/L for ME and 3.6 × 10,7 mol/L for PSE. The recoveries of two alkaloids at three different concentration levels in human urine samples were between 81.7 and 105.0%. The proposed method was successfully applied to the determination of ME and PSE in human urine and the monitoring of pharmacokinetics for PSE. The proposed method has potential in therapeutic drug monitoring and clinical analysis. Copyright © 2009 John Wiley & Sons, Ltd. [source] CE coupled to MALDI with novel covalently coated capillariesELECTROPHORESIS, Issue 4 2010Stefan Bachmann Abstract CE offers the advantage of flexibility and method development options. It excels in the area of separation of ions, chiral, polar and biological compounds (especially proteins and peptides). Masking the active sites on the inner surface of a bare fused silica capillary wall is often necessary for CE separations of basic compounds, proteins and peptides. The use of capillary surface coating is one of the approaches to prevent the adsorption phenomena and improve the repeatability of migration times and peak areas of these analytes. In this study, new capillary coatings consisting of (i) derivatized polystyrene nanoparticles and (ii) derivatized fullerenes were investigated for the analysis of peptides and protein digest by CE. The coated capillaries showed excellent run-to-run and batch-to-batch reproducibility (RSD of migration time ,0.5% for run-to-run and ,9.5% for batch-to-batch experiments). Furthermore, the capillaries offer high stability from pH 2.0 to 10.0. The actual potential of the coated capillaries was tested by combining CE with MALDI-MS for analysing complex samples, such as peptides, whereas the overall performance of the CE-MALDI-MS system was investigated by analysing a five-protein digest mixture. Subsequently, the peak list (peptide mass fingerprint) generated from the mass spectra of each fraction was entered into the Swiss-Prot database in order to search for matching tryptic fragments using the MASCOT software. The sequence coverage of analysed proteins was between 36 and 68%. The established technology benefits from the synergism of high separation efficiency and the structure selective identification via MS. [source] Capillary and microchip electrophoresis in microdialysis: Recent applicationsELECTROPHORESIS, Issue 1 2010Elizabeth Guihen Abstract The theme of this review is to highlight the importance of microscale electrophoretic-based separation systems in microdialysis (,D). The ability of CE and MCE to yield very rapid and highly efficient separations using just nanolitre volumes of microdialysate samples will also be discussed. Recent advances in this area will be highlighted, by illustration of some exciting new applications while the need for further innovation will be covered. The first section briefly introduces the concept of ,D sampling coupled with electrophoresis-based separation and the inherent advantages of this approach. The following section highlights some specific applications of CE separations in the detection of important biomarkers such as low-molecular-weight neurotransmitters, amino acids, and other molecules that are frequently encountered in ,D. Various detection modes in CE are outlined and some of the advantages and drawbacks thereof are discussed. The last section introduces the concepts of micro-total analysis systems and the coupling of MCE and ,D. Some of the latest innovations will be illustrated. The concluding section reflects on the future of this important chemical alliance between ,D and CE/MCE. [source] Capillary electrophoresis using copolymers of different composition as physical coatings: A comparative studyELECTROPHORESIS, Issue 5-6 2006Guillaume L. Erny Abstract In this work, a comparative study on the use of different polymers as physically adsorbed coatings for CE is presented. It is demonstrated that the use of ad hoc synthesized polymers as coatings allows tailoring the EOF in CE increasing the flexibility of this analytical technique. Namely, different polymers were synthesized at our laboratory using different percentages of ethylpyrrolidine methacrylate (EpyM) and N,N -dimethylacrylamide (DMA). Thus, by modifying the percentage of EpyM and DMA monomers it is possible to manipulate the positive charge of the copolymer, varying the global electrical charge on the capillary wall and with that the EOF. These coated capillaries are obtained by simply flushing a given EpyM,DMA aqueous solution into bare silica capillaries. It is shown that by using these coated capillaries at adequate pHs, faster or more resolved CE separations can be achieved depending on the requirements of each analysis. Moreover, it is demonstrated that these coated capillaries reduce the electrostatic adsorption of basic proteins onto the capillary wall. Furthermore, EpyM,DMA coatings allow the reproducible chiral separation of enantiomers through the partial filling technique (PFT). The EpyM,DMA coated capillaries are demonstrated to provide reproducible EOF values independently of the pH and polymer composition with%RSD values lower than 2% for the same day. It is also demonstrated that the coating procedure is reproducible between capillaries. The compatibility of this coating protocol with CE in microchips is discussed. [source] Determination of nitrate and nitrite in rat brain perfusates by capillary electrophoresisELECTROPHORESIS, Issue 9 2004Leyi Gao Abstract A fast and simple method for the direct, simultaneous detection of nitrite (NO2,) and nitrate (NO3,) in rat striatum has been developed using a capillary electrophoresis separation of low-flow push-pull perfusion samples. The method was optimized primarily for nitrite because nitrite is more important physiologically and is found at lower levels than nitrate. We obtained a complete separation of NO2, and NO3, in rat striatum within 1.5 min. Optimal CE separations were achieved with 20 mM phosphate, 2 mM cetyltrimethylammonium chloride (CTAC) buffer at pH 3.5. The samples were injected electrokinetically for 2 s into a 40 cm×75 ,m ID fused-silica capillary. The separation voltage was 10 kV (negative polarity), and the injection voltage was 16 kV (negative polarity). UV detection was performed at 214 nm. The limits of detection obtained at a signal-to-noise ratio (S/N) of 3 for nitrite and nitrate were 0.96 and 2.86 ,M. This is one of the fastest separations of nitrite and nitrate of a biological sample ever reported. Interference produced by the high physiological level of chloride is successfully minimized by use of CTAC in the run buffer. [source] Chemometrics in capillary electrophoresis.JOURNAL OF SEPARATION SCIENCE, JSS, Issue 15-16 2003Part B: Methods for data analysis Abstract Methods for data analysis in CE are addressed to extract relevant information contained in the electrophoretic responses. The main objectives of chemometrics in this field are the characterization of complex samples, the study of peak purity and deconvolution of comigrations, and the quantification of the analytes in poorly resolved peaks. In this paper, the application of chemometric techniques to data analysis is reviewed. The chemometric methods for the optimization of CE separations have been reviewed in Part A (see Sentellas and J. Saurina, Chemometrics in capillary electrophoresis. Part A: Methods for optimization). [source] High-efficiency peptide analysis on monolithic multimode capillary columns: Pressure-assisted capillary electrochromatography/capillary electrophoresis coupled to UV and electrospray ionization-mass spectrometryELECTROPHORESIS, Issue 21 2003Alexander R. Ivanov Abstract High-efficiency peptide analysis using multimode pressure-assisted capillary electrochromatography/capillary electrophoresis (pCEC/pCE) monolithic polymeric columns and the separation of model peptide mixtures and protein digests by isocratic and gradient elution under an applied electric field with UV and electrospray ionization-mass spectrometry (ESI-MS) detection is demonstrated. Capillary multipurpose columns were prepared in silanized fused-silica capillaries of 50, 75, and 100 ,m inner diameters by thermally induced in situ copolymerization of methacrylic monomers in the presence of n -propanol and formamide as porogens and azobisisobutyronitrile as initiator. N -Ethylbutylamine was used to modify the chromatographic surface of the monolith from neutral to cationic. Monolithic columns were termed as multipurpose or multimode columns because they showed mixed modes of separation mechanisms under different conditions. Anion-exchange separation ability in the liquid chromatography (LC) mode can be determined by the cationic chromatographic surface of the monolith. At acidic pH and high voltage across the column, the monolithic stationary phase provided conditions for predominantly capillary electrophoretic migration of peptides. At basic pH and electric field across the column, enhanced chromatographic retention of peptides on monolithic capillary column made CEC mechanisms of migration responsible for separation. The role of pressure, ionic strength, pH, and organic content of the mobile phase on chromatographic performance was investigated. High efficiencies (exceeding 300,000 plates/m) of the monolithic columns for peptide separations are shown using volatile and nonvolatile, acidic and basic buffers. Good reproducibility and robustness of isocratic and gradient elution pressure-assisted CEC/CE separations were achieved for both UV and ESI-MS detection. Manipulation of the electric field and gradient conditions allowed high-throughput analysis of complex peptide mixtures. A simple design of sheathless electrospray emitter provided effective and robust low dead volume interfacing of monolithic multimode columns with ESI-MS. Gradient elution pressure-assisted mixed-mode separation CE/CEC-ESI-MS mass fingerprinting and data-dependent pCE/pCEC-ESI-MS/MS analysis of a bovine serum albumin (BSA) tryptic digest in less than 5 min yielding high sequence coverage (73%) demonstrated the potential of the method. [source] | ||||||||||